TT-Chassis 045 - 45 Watt Extended

Faceplate for TT Kit JTM45

• Material: #LG10 ProReverse Gold glossy lacquered
• Front + Back Panel
• This faceplate is for the TT chassis of the JT45 kit, NOT as replacement faceplate for an original JTM45 chassis.

Files:

• Template

TT-Cabs Headshell based upon the size of the Marshall Small-Head.

Specifications

• Size: ca. 660 x 230 x 210 mm
• Chassis Cut Out: ca. 420 x 58 mm
• Tolex: Marshall Style Levant green
• Hardware: Marshall Style Gold
• Keder / Piping: Gold
• Weight: ca. 5.5 kg
• Wood: 12 mm Birch
• Dovetail joints

[content:3210136]

Clamp for capacitors

• Material: Steel, galvanized
• Diameter: 35 mm

Mounting kit for all TT-Chassis which are designed for mounting with cagenuts and 19" housings

Included are:

• 4 x cagenut M6
• 4 x thread screw M6 x 30

Faceplate for TT Amp-Kit PX45

• Farbe: #LG10 gold GLÄNZEND lackiert
• Material: 1.5 mm Acryl Revers
• Front + Rück Blende

Files:

• Template

• Pri: 120, 230V, 240V @ 50Hz
• (Pri: 0-120V | 0-110-120 V)
• Sec1: 345-0-345V @ 200 mA
• Sec2: 6,3 VCT @ 6A
• Sec3: 5V @ 3A
• Made in Europe.
• Marshall JTM45 Style
• Universal Primärwicklung

Files:

• Datasheet

Output Transformer, replacement for JTM45 with EL34 / 5881 and KT66

• Pri1: 8 kOhm / CT
• Pri2: 6,6 kOhm / CT
• Sec: 4-8-16 Ohm
• Power: 70 Watt
• Made in Europe
• Inductance Primary 8 kOhm: 660 Henry (@240V,50Hz open circuit)
• Inductance Primary 6,6 kOhm: 540 Henry (@240V,50Hz open circuit)
• Minimum Reproducible Frequency at max power (70W): 20Hz/-3dB
• Re(a-a) 8 kOhm: 185ohm +/-5%
• Re(a-a) 6,6 kOhm: 165ohm +/-5%

Files:

• Datasheet

Technical Data:

• Inductance: 3 H

Files:

• Datasheet

Technical Data:

• Inductance: 10 H

Files:

• Datasheet

Faceplate for TT Amp-Kit PX45

• Farbe: #LG10 gold GLÄNZEND lackiert
• Material: 1.5 mm Acryl Revers
• Front + Rück Blende

Files:

• Template

TT PX45 - a  PX18 in combination with the powerstage of the JTM45

Set of componentes for building the TT TT PX45 Guitar Amp.
Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Transformers
  • Power: tt-jtm45-pw
  • Output: tt-otjtm45D, Dual-Primary
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes (12AX7 / ECC83 and EL34)
• Fuses & Fuesholder

NOT INCLUDED:

• Headshell
• Chassis ch045
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

Set of componentes for building the TT  Marshall® Style JTM45 Guitar Amp - EL34 Model.

Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Powertransformer (110,120,230,240V)
• Outputtransformer
• Choke
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes (12AX7, EL34, 5AR4)
• Fuses & Fuesholder

NOT INCLUDED (Please see "Accessories" Tab for suiteable items)

• Chassis
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

Set of componentes for building the TT  Marshall® Style JTM45 Guitar Amp - KT66 Model.

Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Powertransformer (110,120,230,240V)
• Outputtransformer
• Choke
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes (12AX7, KT66, 5AR4)
• Fuses & Fuesholder

NOT INCLUDED (Please see "Accessories" Tab for suiteable items)

• Chassis
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

• Type: Electrolytic can capacitor
• Capacitance: 10 µF
• Voltage Rating: 450 V
• Tolerance: - 20 % / +20 %
• Operating Temperature Range: - 40°C / + 105 °C
• Dimensions: Ø 13 mm x 25 mm
• Termination Style: radial
• Grid: 5,0

Images are for reference only. See Product Specifications

• MPW axial leaded metallized polypropylene film capacitors
• Self Healing
• Low ESR
• Tolerance: +10% @ 1 kHz, 25°C
• Peak, AC voltage (50/60 Hz): 630VDC / 250 VAC
• Size: Ø 8,5 x 14,5 mm
• Dielectric: Polypropylene
• Coating: Flame Retardant Polyester tape wrap (UL510) with epoxy end fill (UL94V0)

• MPW axial leaded metallized polypropylene film capacitors
• Self Healing
• Low ESR
• Tolerance: +10% @ 1 kHz, 25°C
• Peak, AC voltage (50/60 Hz): 630VDC / 250 VAC
• Size: Ø 6,5 x 14,5 mm
• Dielectric: Polypropylene
• Coating: Flame Retardant Polyester tape wrap (UL510) with epoxy end fill (UL94V0)

• MPW axial leaded metallized polypropylene film capacitors
• Self Healing
• Low ESR
• Tolerance: +10% @ 1 kHz, 25°C
• Peak, AC voltage (50/60 Hz): 630VDC / 250 VAC
• Size: Ø 6 x 14,5 mm
• Dielectric: Polypropylene
• Coating: Flame Retardant Polyester tape wrap (UL510) with epoxy end fill (UL94V0)

• MPW axial leaded metallized polypropylene film capacitors
• Self Healing
• Low ESR
• Tolerance: +10% @ 1 kHz, 25°C
• Peak, AC voltage (50/60 Hz): 630VDC / 250 VAC
• Size: Ø 6,5 x 14,5 mm
• Dielectric: Polypropylene
• Coating: Flame Retardant Polyester tape wrap (UL510) with epoxy end fill (UL94V0)

• MPW axial leaded metallized polypropylene film capacitors
• Self Healing
• Low ESR
• Tolerance: +10% @ 1 kHz, 25°C
• Peak, AC voltage (50/60 Hz): 630VDC / 250 VAC
• Size: Ø 6,5 x 14,5 mm
• Dielectric: Polypropylene
• Coating: Flame Retardant Polyester tape wrap (UL510) with epoxy end fill (UL94V0)

Panel Mount Potentiometer - Push / Pull

• Power Rating: 0,125 W
• Voltage Rating: 150 V AC
• Tolerance: 20%
• Shaft: 6,35 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M7 (6,8 mm)
• Termination: PCB
• Dimension: 16 mm
• Switch: DPDT

Mica Capacitors

• Voltage Rating:    500 V
• Tolerance: 5%
• Operating Temperature Range: - 50°C / + 150°C
• Termination Style: radial

Mica Capacitors

• Voltage Rating:    500 V
• Tolerance: 5%
• Operating Temperature Range: - 50°C / + 150°C
• Termination Style: radial

TT PX45 - a  PX18 in combination with the powerstage of the JTM45

Set of componentes for building the TT TT PX45 Guitar Amp.
Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Transformers
  • Power: tt-jtm45-pw
  • Output: tt-otjtm45D, Dual-Primary
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes (12AX7 / ECC83 and EL34)
• Fuses & Fuesholder

NOT INCLUDED:

• Headshell
• Chassis ch045
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !