Fuseholder 5x20 mm

TT-Chassis Aluminium - Typ 040

Chassis for the PX18/PI18 kit, fits in all of our Standard Smallhead and 18W Headcabs and Combos

• Size : 430 x 170 x 65 mm
• Material: 2 mm Aluminium
• Made in Germany
• fits Alpha 3/8" Potentiometer (Intemnumber p38-*)
• Mounting: with cage nuts (not included)

Files:

• Datasheet

Tube-Town Marshall Style18 Watt Chassis

• Size: (WxHxD) 432 x 170 x 65 mm
• Material: 2 mm Aluminium (AllMg3)
• reinforced corners (V2020 and above)

Please see also the list with recommended accessories !

Files:

• Datenblatt V2020
• Template 18W Faceplate
• Template Faceplates

• Marshall 18 Watt Style Chassis - 1974
• for use in a combo
• Size: (WxHxD) 530 x 65 x 152 mm
• Material: 2 mm Aluminium (AllMg3)
• Mounting: with cage nuts (not included)

Files:

• Datasheet (PDF)
• Template Faceplate

• Extended JTM45 Chassis
• Size: (WxHxD) 432 x 65 x 170 mm
• PT cut-out: 70 x 69 mm
• Material: 2 mm Aluminium (AllMg3)
• Made in Germany

Files:

• Datasheet

Aluminium chassis based on the YAH100 chassis, but without cut-outs, drillings etc.

• Size: 483 x 238 x 70 mm
• Material: 2 mm AlMg3
• Reinforced corner joints
• Net Weight ca. 1,4 kg
• Mounting: with cage nuts (not included)
• Made in Germany

Files

• Faceplate Template

• Extended JTM45 Chassis
• Size: (WxHxD) 432 x 63 x 170 mm
• PT cut-out: 70 x 69 mm
• Material: 1,5 mm Steel, galvanize
• Made in Germany

Files:

• Datasheet

Same as the Chassis 040 - PX18 but with with octal sockets for the powertubes, fits in all of our Standard Smallhead and 18W Headcabs and Combos

• Size : 432 x 170 x 65 mm
• Material: 2 mm Aluminium
• Mounting: with cage nuts (not included)

Files:

• Datasheet

This chassis is based on a regular HiWatt chassis which was used for amplifiers up to 100 Watt. The chassis was adapted and optimized for the YAH100 kit but get used for other HiWatt Clones too.

• Size: 483 x 238 x 70 mm
• Material: 1,5 mm Steel
• hot zinc dipped
• Reinforced corner joints
• Made in Germany
• Mounting: with cage nuts (not included)

Files

• Faceplate Template

TT-Chassis Aluminium - Typ 042

Chassis for the JC18 kit, fits in all of our Standard Smallhead and 18W Headcabs and Combos and of course the JC18 headshell

• Size : 432 x 170 x 65 mm
• Material: 2 mm Aluminium

Files:

• Datasheet

Marshall Style Knob, Gold

• Material: Phenolic
• Shaft Size: 6 - 6,4 mm
• Size: 19,5 x 15,3 mm
• Mounting: Set-Screw, hexagon

Marshall Style Knob, Gold

• Material: Phenolic
• Shaft Size: 6 mm, knurled
• Size: 19,5 x 15,3 mm
• Mounting: Push-On, no D-Shaft

• Type: Rocker Switch
• Version: DPST  ON-OFF, Lighted red, labeled I/O
• Recess: 30 x 22 mm, Snap-in mount
• Rating: max. 16A/250V AC
• Termination Style: solder lug / quick-connect terminals

SCI R13-29B High Current DPDT On-On Toggle Switch

The SCI R13-29B is a high current DPDT toggle switch (double pole double throw), designed for use in high current applications.

Specifications

• Type: Toggle switch with metal lever
• Design: 2-Pole ON-ON switch
• Mounting Ø: 12.2 mm
• Switching capacity: 15A@125VAC / 10A@250VAC
• Switch type: DPDT (double pole double throw)

Vacuum Tube Damper made of silicon, helps to reduce noise and rattle of vacuum tubes. But it will not turn a bad tube into a good tube.
If a higher level of damping is needed, than use more than one damper per tube.

• Inner diameter ca. 22 mm
• Can not be used with JJ 12AX7 and other JJ preamp tubes with similar diameter and JJ EL84 and JJ EL844
• Price per damper

BEFORE ordering check the exact outer diameter of the vacuum tubes and compare it with the diameter of the damper to make sure that the damper fits.

• 19" Housing, with ventilation slots in top panel
• 1,2 mm steel, black powder coated
• Front panel, 3 mm Aluminium, black powder coated
• Flat-packed with screws
• Depth: 250 mm
• 2 U

• Type: Toggle Switch
• Version: SPSD Momentary, ON-(ON)
• Assembly Ø: 6.2 mm
• Rating: 3 A / 250VAC, 6 A / 125VAC
• Termination Style: solder-lugs
• Size: 13 x 7,8 x 10,4 mm