TT Diffusor 12" - Standard

The 12” Veteran 30™ speaker from WGS is tonally superior to Celestion's™ Vintage 30™ speaker. The tonal improvement is in the upper-mids. The Veteran 30™ speaker has smoothed out the upper-mid "spike" notorious in the Vintage 30™ speaker.

Unit Weight:  10 pounds

Mounting Information

• Diameter:12.2”
• Overall depth: 5.3”
• Cut-out diameter: 11.1”
• Mounting slot dimensions: 0.31”
• Number of mounting slots: 8

Thiele-Small Parameters

• Resonant Frequency (Fs): 94.84 Hz
• DC Resistance (Re): 7.99 Ohm
• Coil Inductance (Le): 0.35 mH
• Mechanical Q (Qms): 12.15
• Electromagnetic Q (Qes): 0.78
• Total Q (Qts): 0.74
• Compliance Equiv. Vol. (Vas): 18.53 cu ft
• Mech. Compliance of Susp. (Cms): 0.10 mm/N
• BL Product (BL): 13.25 T-M
• Diaphragm Mass Inc. Airload (Mms): 28.88 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.84 db

Ten 30

Rich and expressive, the Ten 30 combines warm lows with a vocal mid-range and an articulate top end. The clean sound is open and revealing; push hard and you're rewarded with full-blooded Celestion grind.

General specifications

• Nominal diameter: 10", 254mm
• Power rating: 30Wrms
• Nominal impedance: 8 Ohm
• Sensitivity: 95dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.25", 31.25mm
• Voice coil material: Round copper
• Magnet type: Ceramic
• Magnet weight: 13oz, 0.37kg
• Frequency range: 85-5000Hz
• Resonance frequency, Fs: 93.9Hz
• DC resistance, Re: 6 Ohm

Mounting Information

• Cut-out diameter: 9.0", 229mm
• Diameter: 10.1", 256mm
• Magnet structure diameter: 3.8", 96mm
• Mounting slot dimensions: 0.24 x 35", 6 x 9mm
• Mounting slot PCD: 9.6", 245mm
• Number of mounting slots: 8
• Overall depth: 3.8", 96mm
• Unit weight: 3.5lb, 1.6kg

The ET90 is our lastest addition to the ET65 lineage.  Taking its core sound from the ET65, the ET90 gives you more all the way around.  We went to larger motor and a beefier voice coil on this model.  The result is more headroom, more power handling and a bigger feel.  If you've been looking for classic British tone with an "open" feel and a lot of power, the ET90 is your new favorite.

Thiele-Small Parameters

• Resonant Frequency (Fs): 100.14 Hz
• DC Resistance (Re): 8.04 Ohm
• Coil Inductance (Le): 0.33 mH
• Mechanical Q (Qms): 6.08
• Electromagnetic Q (Qes): 0.78
• Total Q (Qts): 0.69
• Compliance Equiv. Vol. (Vas): 16.03 cu ft
• Mech. Compliance of Susp. (Cms): 0.08 mm/N
• BL Product (BL): 13.95 T-M
• Diaphragm Mass Inc. Airload (Mms): 29.95 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.94 db

The Peacekeeper is a revolutionary new attenuating speaker for guitarists from Celestion. It’s the simplest and most toneful way of being able to dial your amplifier right up to its “sweet spot”, while keeping the decibel levels down.

Featuring a unique dual voice coil design, this attenuating speaker works together with an amp, like a conventional guitar speaker, only with significantly reduced output sensitivity. Enabling you to drive your amplifier harder while still listening at reasonable volume levels. Load it into your cab and the Peacekeeper will attenuate your amplifier in the most natural way possible, with zero additional colouration or tonal compromise.

General Specifications

• Nominal diameter: 12", 305mm
• Power rating: 50 Wrms
• Nominal impedance: Available 8Ω
• Sensitivity: 86 dB
• Chassis type: Pressed steel
• Voice coil material: Round copper
• Magnet type: Ceramic
• Magnet weight: 50oz, 1.42kg
• Frequency range: 70-5000Hz
• Resonance frequency, Fs: 80Hz

Mounting Information

• Cut-out diameter: 11.1", 283mm
• Diameter: 12.2", 309mm
• Magnet structure diameter: 6.1", 156mm
• Mounting slot dimensions: 0.31", 7.9mm Ø
• Mounting slot PCD: 11.7", 297mm
• Number of mounting slots: 4
• Overall depth: 5.3", 135mm
• Unit weight: 10.6lb, 4.8kg

Finally, the wait is over.   We have created a 10" speaker that captures all the tone and mojo of our extremely popular 12" Green Beret.   The Green Beret 10 boasts the same midrange push, articulate top end and warm, harmonically rich breakup of its larger namesake.  It also sports an impressive amount of low end for a 10" speaker.   With a 1.5" voice coil and a paper former, this speaker drips with vintage tone.    If you've been looking for classic British tone in a 10" speaker the Green Beret 10 delivers.

Finally, the wait is over. We have created a 10" speaker that captures all the tone and mojo of our extremely popular 12" Green Beret.   The Green Beret 10 boasts the same midrange push, articulate top end and warm, harmonically rich breakup of its larger namesake.  It also sports an impressive amount of low end for a 10" speaker.   With a 1.5" voice coil and a paper former, this speaker drips with vintage tone.    If you've been looking for classic British tone in a 10" speaker the Green Beret 10 delivers.

Tube-Town Review: Due to the smooth cone used in the 10" WGS Green Beret, its top end is much more subtle compared to the original 12" Celestion Greenback G12M, but also to the 10" Celestion Greenback. However, the midrange is not overemphasized and the whole speaker sounds full and balanced, with a distinct "American touch" to the overall sound.
We recommend the 10" Green Beret for everything from blues to rock to modern metal, but less so for blackface-typical clean sounds, for which there are better suited 10" speakers. In order for the speaker to develop its full sonic spectrum, it should be used either in an open cabinet or combo, or in a large-volume closed cabinet. A closed cabinet that is too small will dampen the speaker too much and cut the sound.
The WGS 10" Green Beret is also a real upgrade for many budget combos that are equipped with inexpensive 10" speakers and often sound a bit thin and sharp, especially when it comes to harder tones.

Thiele-Small Parameters

• Resonant Frequency (Fs): 117.31 Hz
• DC Resistance (Re): 6.8 Ohm
• Coil Inductance (Le): mH
• Mechanical Q (Qms): 9.429
• Electromagnetic Q (Qes): 1.884
• Total Q (Qts): 1.57
• Compliance Equiv. Vol. (Vas): 15.59 cu ft
• Mech. Compliance of Susp. (Cms): 0.082 mm/N
• BL Product (BL): 11.71 T-M
• Diaphragm Mass Inc. Airload (Mms): 22.4417 grams
• Surface Area of Cone (Sd): 336.0962 cm squared
• Sound Pressure Level (spl): 96.62 db

With a 90-watt power rating, the Celestion Cream is purpose-built for vintage tones, whatever kind of amp you use. By applying new technologies and manufacturing methods developed during the creation of our Creamback speakers, we’ve been able to deliver a higher power rating while preserving the very essence of an alnico guitar speaker.

Delivering a glorious, laid-back attack, the Cream exudes warm lows and a brilliant bell-like chime. It has smooth and organic mids, further characterised by a fine-grained detail that adds a high-definition quality to the vocal range.

The Cream has been specially created to bring alnico class to all kinds of amps from 1-watt to 90-watts. It conveys a satisfying warmth, detailed expressiveness and exceptional musicality, even at low power levels.

General Specifications

• Nominal diameter: 12", 305mm
• Power rating: 90W
• Nominal impedance: 8Ω
• Sensitivity: 100dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.75", 44.5mm
• Voice coil material: Round copper
• Magnet type: Alnico
• Frequency range: 75-5000Hz
• Resonance frequency, Fs: 75Hz
• DC resistance, Re: 6.7Ω
• Made in UK

Vintage American Ceramic Guitar Speaker
10" seamed cone speaker with a small ceramic motor, an upgrade replacement for Jensen C10R.

• Power: 25 W
• Small ceramic magnet
• weight: 1,4 kg
• VC diameter: 1"
• sensitivity: 96,5 dB
• 4 Ohm

Vintage American Ceramic Guitar Speaker – Super Ribbed Cone
12" seamed cone speaker with a small ceramic motor, an upgrade replacement for Jensen C12R.

• Magnet:  Small Ceramic
• Power: 25W
• Sensitivity: 97,5dB
• Weight: 1,7 kg
• VC Diameter: 1″
• 4 Ohm

The Ruby is an alnico-magnet guitar speaker that’s purpose-built to create vintage tones – and at 35-watts power handling it’s ideal for use with mid-powered amps and combos.
Bringing the instantly familiar Celestion alnico vibe with its glorious dampened attack; the Ruby oozes a richly musical vintage warmth with mellow highs and a smooth sophisticated midrange.

Specifications

• Nominal diameter 305mm / 12in
• Power rating 35W
• Rated impedance 8Ω or 16Ω
• Sensitivity 100dB
• Chassis type Pressed steel
• Magnet type Alnico
• Voice coil diameter 1.75in / 44mm
• Voice coil material Round copper
• Frequency range 75-5000Hz
• Resonance frequency, Fs 75Hz
• DC resistance, Re 6.7Ω or 13.1Ω

Mounting Information

• Cut-out diameter 283mm / 11.1in
• Diameter 309mm / 12.2in
• Magnet structure diameter 128mm / 5.0in
• Mounting hole dimensions 7.9mm / 0.31in Ø
• Mounting hole PCD 297mm / 11.7in
• Number of mounting holes 8
• Chassis depth (inc gasket) 92mm / 3.63in
• Magnet depth 73mm / 2.87in
• Overall depth 165mm / 6.5in
• Unit weight 4.2kg / 9.3lb

The original G12M of the 1960s was Celestion's first guitar speaker to use a ceramic magnet and paved the way for high power guitar amplifiers. The G12M uses a medium weight magnet to produce a sound that is smooth and warm but bright enough to hold its own against any rock backline.Known simply these days as the 'Greenback', the G12M's fabled 'brown tone' is characterised by a warm, controlled low-end, a rich, vocal mid-range and a delicate, detailed top-end. Loaded into a 4x12 and driven hard, these speakers exude warm, crunchy chords and sweet searing single-notes

General Specifications

• Nominal diameter: 12", 305mm
• Power rating:20Wrms
• Nominal impedance: 8Ω and 15Ω
• Sensitivity: 96dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.75", 44.5mm
• Voice coil material: Round copper
• Magnet type: Ceramic
• Magnet weight: 35oz, 0.99kg
• Frequency range: 75-5000Hz
• Resonance frequency, Fs: 75Hz
• DC resistance, Re: 6.57Ω and 12.13Ω

Mounting Information

• Cut-out diameter: 11.1", 283mm
• Diameter: 12.2", 309mm
• Magnet structure diameter: 5.9", 150mm
• Mounting slot PCD: 11.7", 297mm
• Number of mounting slots: 4
• Overall depth: 5.1", 130mm
• Unit weight: 7.9lb, 3.6kg

CERAMIC Vintage

The JENSEN® "C" series speakers were developed because the world's supply of cobal (Co in AlNiCo) slump, making this raw material more expensive. While ceramic magnets are larger in size than comparable AlNiCo magnets of the same gauss strenght, their cost is lower. "C" series JENSEN® speakers use same cones and voice coils comparable to our AlNiCo series speakers, thus providing a similar tone but at a reduced price.

Technical Details:    

• Size: 10"
• Impedance: 8 Ohm
• Rated Power (RMS): 35 W
• Sensitivity @ 1 W, 1 m: 95,2 dB
• Resonance Frequency  fs: 96 Hz

Files:

• Datasheet

The 40 watt version of the Jensen Blackbird has smoother top end compared to the 100 watt version, making it suitable not only for crisp clean sounds but also good for crunchy leads.

Gene: Blues, Jazz, Rock'n Roll, Rockabilly

Technical Details:    

• Size: 12"
• Impedance: 16 Ohm
• Rated Power (RMS): 40 W
• Sensitivity @ 1 W, 1 m: 96 dB
• Resonance Frequency  fs: 93,2 Hz

Thiele/Small Parameter (8 Ohm Version)

• Re: 5.9 Ω
• Fs: 93.2 Hz
• Qms: 14.29
• Mms: 28.7 g
• Qts: 1.36
• Bxl: 8.20 Tm
• Cms: 102 µm/N
• Sd: 490.9 cm²
• Vas: 34.6 l
• Le (1kHz): 0.40 mH

The G8C ceramic speaker will breathe new life into your small combo.  This little monster puts out some serious sound. A serious upgrade for your Fender Champ.

Thiele-Small Parameters (8 Ohm Speaker)

• Resonant Frequency (Fs): 148.07 Hz
• DC Resistance (Re): 6.7 Ohm
• Coil Inductance (Le): 8 mH
• Mechanical Q (Qms): 9.6715
• Electromagnetic Q (Qes): 0.9538
• Total Q (Qts): 0.8682
• Compliance Equiv. Vol. (Vas): 0.257 cu ft
• Mech. Compliance of Susp. (Cms): 110.714 mm/N
• BL Product (BL): T-M
• Diaphragm Mass Inc. Airload (Mms): 10.4353 grams
• Surface Area of Cone (Sd): 214.0839 cm squared
• Sound Pressure Level (spl): 95.78 db

Featured in the world's top selling 4x12 cabinet, the G12T-75 is a high powered rock player's dream.

Built to meet the demands of high gain amplifiers, the G12T-75 combines a huge, tightly controlled low-end and aggressive mid-range with a softened top-end that adds a welcome sweetness to overdrive, distortion and aggressive upper harmonics. These are the characteristics that make the G12T-75 the weapon of choice for Yngwie Malmsteen.

General Specifications

• Nominal diameter: 12", 305mm
• Power rating: 75Wrms
• Nominal impedance: Available 8Ω or 16Ω
• Sensitivity: 97dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.75", 44.5mm
• Voice coil material: Round copper
• Magnet type: Ceramic
• Magnet weight: 35oz, 0.99kg
• Frequency range: 80-5000Hz
• Resonance frequency, Fs: 85Hz
• DC resistance, Re: Available 6.77Ω or 12.9Ω

Mounting Information

• Cut-out diameter: 11.1", 283mm
• Diameter: 12.2", 309mm
• Magnet structure diameter: 5.7", 145mm
• Mounting slot dimensions: 0.31", 7.9mm Ø
• Mounting slot PCD: 11.7", 297mm
• Number of mounting slots: 4
• Overall depth: 5.0", 127mm
• Unit weight: 7.7lb, 3.5k

Balance, punch, fullness, and clarity are at the forefront of this speaker. The mids are tailored and even, enabling the articulation, openness, air, and a nice glassiness to shine through in the highs. The tight, solid, and responsive lows round out the tone and perfectly balance the detail in the highs. A very musical speaker optimized for the ever so popular Deluxe Reverb, but suitable anywhere you want pure American tone.

Spzification:

• Nominal Impedance(Z): 16 Ohm
• Rated Power IEC268-5: 50 Watt
• Sensitivity (@1W/1 m): 100 dB/SPL
• Frequency range: 80 – 5000 Hz
• Resonant Frequency (Fs): 90 Hz
• Voice Coil Diameter: 1,75"

Files:

• Datasheet

Turn heads with this 8" hempen guitar speaker, the Detroit 820. This model brings out an organic and vintage tweed sound, creating warm and full lows, strong and barky mids, and creamy highs to round out the top end.

The Detroit 820 is the perfect choice for guitarists looking for an upgrade to their blues or rock tone. High sensitivity, a hemp composite cone, a powerful ferrite magnet, dual-lug terminals for easy connectivity, and a sturdy steel basket come together to enhance your style and sound to make you the talk of the town.

American tone guitar speaker

• 8" (203 mm) steel basket diameter
• 20 watts, 4 ohm, 94 dB SPL
• 1" copper voice coil, Kraft paper former
• 10 oz ferrite magnet
• USA-made hemp cone
• Size, Nominal (inch & mm): 8" (203 mm)
• RoHS Compliant: Yes
• Nominal Impedance (Z) (Ω): 4
• Rated Power IEC268-5 (W): 20 Watts
• Rated Impedance (Ω): 4
• Continuous Power (W): 20
• Program Power (W): 40
• Frequency Range (Hz): 80 - 10,000
• Sensitivity (dB SPL) ¹: 94
• Resonant Frequency (Fs) (Hz): 139
• DC Resistance (Re) (Ω): 3.4
• Voice Coil Inductance (Le) (mH): 0.12
• Mechanical Q Factor (Qms): 15.36
• Electrical Q Factor (Qes): 4.45
• Total Q Factor (Qts): 3.45
• Mechanical Resistance (Rms) (kg/s): 0.47
• Compliance Equivalent Volume (Vas) (L): 10.92
• Suspension Compliance (Cms) (mm/N): 0.16
• Surface Area of Diaphragm (Sd) (cm²): 221.67
• Moving Mass (Mms) (gm): 8.28
• Magnetic Gap Height (mm): 6.0
• Coil Winding Height (mm): 6.35
• Motor Force Factor (BL) (T•M): 2.36
• Efficiency (η₀) (%): 0.64
• Efficiency Bandwidth Product (EBP) (Fs/Qes): 31.46
• Basket Type: Stamped steel with black powder coat
• Terminal Size (mm): 5.2 x 0.5
• Voice Coil Wire Material: Copper
• Voice Coil Former Material: Nomex
• Voice Coil Winding Style: Single Layer
• Magnet Material: Ferrite
• Magnet Weight (g): 283.5
• Cone Body Material: Hemp
• Dust Cap Material: Felt
• Spider Material: Cotton
• Net Weight (kg): 1.01

It's hard to escape the sound of the G12H, just listen to any Hendrix recording and chances are you'll be hearing a whole raft of them powering the guitar out of the mix.

These faithful re-creations capture the unmistakeable mojo of late 60s rock guitar tones. Unsurpassed in a 4x12 for cranking out towering, huge power chords, the Heritage Series G12H (55) features the 55c/s 'bass' cone. This model is famous for its thick syrupy tones, with a deep growling back end, densely complex mid-range and a finely detailed top end.

General Specifications

• Nominal diameter: 12", 305mm
• Power rating: 30Wrms
• Nominal impedance: Available 8Ω or 15Ω
• Sensitivity: 100dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.75", 44.5mm
• Magnet type: Ceramic
• Magnet weight:50oz, 1.42kg
• Frequency range: 55-5000Hz
• Resonance frequency, Fs: 55Hz
• DC resistance, Re: 6.53Ω and 12.11Ω

Mounting Information

• Cut-out diameter: 11.1", 283mm
• Diameter: 12.2", 309mm
• Magnet structure diameter: 6.6", 168mm
• Mounting slot PCD: 11.7", 297mm
• Number of mounting slots: 4
• Overall depth: 5.3", 135mm
• Unit weight: 10.4lb, 4.7kg

Following the great reviews we received for the Gold 12", we realised there was also a need for a speaker that conveyed the Alnico mellowness of the original Blue, with the speed and response of a 10" driver.The G10 Gold is the ultimate 10" speaker, blending unmistakable Alnico class with a rich low-end, creamy mid-range and vintage chiming top-end. Springy, warm, revealing and highly expressive, it can be used singly or in pairs to add a classy sheen to any amp, or in a 4x10 configuration for higher volume depth, warmth and shimmer, with less of the boom associated with 4x12 cabinets. General Specifications

• Nominal diameter: 10", 254mm
• Power rating: 40Wrms
• Nominal impedance: Available 8Ω or 15Ω
• Sensitivity: 98dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.75", 44.5mm
• Voice coil material: Round copper
• Magnet type: Alnico
• Frequency range: 80-6000Hz
• Resonance frequency, Fs: 80Hz
• DC resistance, Re: 6.66Ω and 13.56Ω

Mounting Information

• Cut-out diameter: 9.0", 229mm
• Diameter: 10.1", 256mm
• Magnet structure diameter: 4.7", 119mm
• Mounting slot dimensions: 0.25", 6.5mm Ø
• Mounting slot PCD: 9.6", 244mm
• Number of mounting slots: 8
• Overall depth: 5.3", 135mm
• Unit weight: 6.0lb, 2.7kg

High-quality headshell for Mesa Mark II / III and similar amp chassis, with a cutout in the bottom for the use of a reverb tank.
The headshell is made of high quality oak, for chassis with a size of 432 x 216 x 60 mm . The high-gloss finish gives the surface a vibrant look, while the dovetail joints complete the look.
Chassis mounting holes must be drilled by the customer depending on the existing chassis and mounting methods.

Specification:

• Size (W x H x D, Outside): ca 474 x 210 x 257 mm
• Designed for Mesa "Short" chassis with dimensions: 432 x 216 x 60 mm
• Solid wood glossy Oak
• Hardware: leather case handle light brown
• Weight: approx. 5 kg

[content:3210136]

Panel Mount Potentiometer

• Power Rating: 0,125 W
• Voltage Rating: 150 V AC
• Tolerance: 20%
• Shaft: 6,3 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M7 (6,8 mm)
• Termination: Solder lugs
• Dimension: 16 mm

• Type: Fender Blackface Style Knob
• Material: Phenolic
• Shaft Size: 6 - 6,3 mm
• Size: 30 x 16,1 mm
• Mounting: Set-Screw

Panel Mount Potentiometer

• Power Rating: 0,125 W
• Voltage Rating: 150 V AC
• Tolerance: 20%
• Shaft: 6,3 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M7 (6,8 mm)
• Termination: Solder lugs
• Dimension: 16 mm

Universal size for 12" speakers
Dome diameter: 120 mm - recommended for guitar loudspeaker with massive beaming and higain sounds

As the frequency increases, the radiation of a loudspeaker is increasingly focused on its center. If the listener is in this beam, the sound is extremely harsh and biting; if one moves to the side of it, the sound becomes significantly darker and treble components are partially missing.
To reduce this behavior, a diffuser is used. This sits directly in the beam of the speaker and deflects the high frequencies very strongly, it breaks the "beam". This makes the sound much fuller and more balanced.

Hear the Diffusor in action on ->YouTube (made by one of our customers, Thanks !)