Main page » Tubes » JJ-Electronic » JJ 5751

JJ 5751

This tube is recommend to tame the gain of an amp and make it sound "sweeter". The 5751 has only a gain of 70 instead of 100 like the typical 12AX7/ECC83 tube type and can be used as a drop in replacement for 12AX7 / ECC83 tubes.

Files:

Datasheet

Manufacturer

Herstellerinformationen | Manufacturer Information
JJ Electronic
A. Hlinku 3
022 01 ČADCA
Slowakische Republik
www.jj-electronic.com

Customer reviews (2)

Essential information about customer reviews We do not verify that the published reviews come from such consumers who have actually used or purchased the rated goods or services. All reviews, i.e. positive and negative, are published. No reviews that are unobjective, offensive or unrelated to the product will be published.

Unfortunately there are no review yet. Be the first who rate this product.

Customers who bought this product bought also the following products:

WGS G8C 8" / 20 W / 4 Ohm

The G8C ceramic speaker will breathe new life into your small combo. This little monster puts out some serious sound. A serious upgrade for your Fender Champ.

Thiele-Small Parameters

Resonant Frequency (Fs): 148.07 Hz
DC Resistance (Re): 6.7 Ohm
Coil Inductance (Le): 8 mH
Mechanical Q (Qms): 9.6715
Electromagnetic Q (Qes): 0.9538
Total Q (Qts): 0.8682
Compliance Equiv. Vol. (Vas): 0.257 cu ft
Mech. Compliance of Susp. (Cms): 110.714 mm/N
BL Product (BL): T-M
Diaphragm Mass Inc. Airload (Mms): 10.4353 grams
Surface Area of Cone (Sd): 214.0839 cm squared
Sound Pressure Level (spl): 95.78 db

69,00 €

TT 12AX7 / ECC83 Classic V1

TT Selection: V1 - Low Noise
This tube is selected for sensitive input stages (V1)

The TT12AX7 impresses with its fine and detailed reproduction of the highs, which is maintained even at high amplification levels. Due to a higher H3 part, the TT12AX7 sounds significantly cleaner than many other 12AX7/ECC83 tubes, which makes the bass range appear much tighter. We therefore especially recommend this tube for styles such as clean, crunch, and metal, where high amplification and clear transparency are required.

Electrical Characteristics

Heater voltage (Uf): 6.3V or 12.6V
Heater current (If): 300mA at 6.3V, 150mA at 12.6V
Anode voltage (Ua): Maximum 300V
Grid voltages (Ug1): -2V (typical)
Grid voltages: -50V to 0V
Anode current (Ia): 1.2mA (typical)
Anode power dissipation: Maximum 1W per triode
Anode resistance (ra): 62.5kΩ
Amplification factor (μ): 100
Transconductance (S): 1.6mA/V
Input capacitance (Cin): 1.6pF
Output capacitance (Cout): 1.6pF

Mechanical Characteristics

Socket: B9A (Noval)
Number of pins: 9

Pin Configuration

1 Anode (Triode 1)
2 Grid (Triode 1)
3 Cathode (Triode 1)
4 Heater (f)
5 Heater (f)
6 Anode (Triode 2)
7 Grid (Triode 2)
8 Cathode (Triode 2)
9 Center Heater (f)

Application Notes

Heater operation: The tube can be operated with 6.3V or 12.6V, depending on the circuit design.
Grid resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable functionality.
Coupling capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high-frequency interference.