EH 12AX7 / ECC83 V1
EH 12AX7 / ECC83 V1
TOP

EH 12AX7 / ECC83 V1

Product No.:
eh12ax7-v1
In stock. Delivery time depends on the destination country* In stock. Delivery time depends on the destination country*
RoHs:
conform
Weight:
0.018 kg per piece
24,21 €

incl. VAT excl. Shipping costs

Customers who bought this product bought also the following products:

Sovtek 5AR4 / GZ34
23,80 €
TT 12AT7 / ECC81
Warm and balanced overall sound, paired with high resolution and brilliance, which is why the TT12AT7 achieves the best results in both instrumental and audio/high-end amplifiers.

Features:
  • Warm and balanced sound
  • Excellent sound resolution and brilliance
  • Ideal for instrumental and audio/high-end amplifiers

Hint;
Often, 12AU7 and 12AT7 types are used instead of 12AX7 tubes in order to either reduce the overall power of the amplifier or just take back the overdrive of the preamp. Especially the 12AU7 brings a very large tonal difference compared to a 12AX7, which is usually much greater than when switching from a 12AX7 to 5751 or 12AT7.

When using a 12AU7 in a driver stage that is normally designed for 12AX7, the overall power of the power amp is usually reduced. How big this difference is depends on the amplifier or circuit. For example, a Marshall with a 12AX7 in the phase inverter stage set to volume 5 will then reach the same volume with a 12AU7 set to volume 6 (perceived volume, not measured).

Electrical Characteristics

  • Heater Voltage (Uf): 6.3V or 12.6V
  • Heater Current (If): 300mA at 6.3V, 150mA at 12.6V
  • Anode Voltage (Ua): Maximum 300V
  • Grid Voltage (Ug1): -2V (typical)
  • Anode Current (Ia): 10mA (typical)
  • Anode Power Dissipation: Maximum 2.5W per triode
  • Anode Resistance (ra): 11kΩ
  • Amplification Factor (μ): 60
  • Transconductance (S): 5.5mA/V
  • Input Capacitance (Cin): 1.6pF
  • Output Capacitance (Cout): 1.6pF

Mechanical Characteristics

  • Socket: B9A (Noval)
  • Number of Pins: 9

Pin Configuration

  • 1 Anode (Triode 1)
  • 2 Grid (Triode 1)
  • 3 Cathode (Triode 1)
  • 4 Heater (f)
  • 5 Heater (f)
  • 6 Anode (Triode 2)
  • 7 Grid (Triode 2)
  • 8 Cathode (Triode 2)
  • 9 Center Heater (f)

Application Notes

  • Heater Operation: The tube can be operated with either 6.3V or 12.6V, depending on the circuit design.
  • Grid Resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable operation.
  • Coupling Capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high frequency disturbances.
16,90 €
Mullard 12AX7 / ECC83 Reissue
Mullard 12AX7 / ECC83 Reissue, with long plates
39,00 €
Mullard 12AU7 / ECC82 Reissue

Mullard 12AU7 / ECC82 Reissue, Made in Russia

38,00 €
Shield Noval yellow
Tube Shield Noval
  • for noval sockets
  • Color: yellow
  • High: 55 mm
  • Including Base and Shield
1,25 €
JJ EL844 - QUAD

4 tubes, matched as quad

JJ developed a completly new tube which is compatible with the EL84. The difference lies in the around 25% decreased headroom. This will give you the benefit to get the often desired power amp overdrive at lower volume levels. We recommend this tube for low wattage amps to get a better sound at bedroom levels.

Please check the datasheet!

Files:

73,00 €
18,25 € per Piece
TT 12AX7 / ECC83 Classic V1
TT Selection: Balanced
Both systems with balanced gain


The TT12AX7 impresses with its fine and detailed reproduction of the highs, which is maintained even at high amplification levels. Due to a higher H3 part, the TT12AX7 sounds significantly cleaner than many other 12AX7/ECC83 tubes, which makes the bass range appear much tighter. We therefore especially recommend this tube for styles such as clean, crunch, and metal, where high amplification and clear transparency are required.

Electrical Characteristics

  • Heater voltage (Uf): 6.3V or 12.6V
  • Heater current (If): 300mA at 6.3V, 150mA at 12.6V
  • Anode voltage (Ua): Maximum 300V
  • Grid voltages (Ug1): -2V (typical)
  • Grid voltages: -50V to 0V
  • Anode current (Ia): 1.2mA (typical)
  • Anode power dissipation: Maximum 1W per triode
  • Anode resistance (ra): 62.5kΩ
  • Amplification factor (μ): 100
  • Transconductance (S): 1.6mA/V
  • Input capacitance (Cin): 1.6pF
  • Output capacitance (Cout): 1.6pF

Mechanical Characteristics

  • Socket: B9A (Noval)
  • Number of pins: 9

Pin Configuration

  • 1 Anode (Triode 1)
  • 2 Grid (Triode 1)
  • 3 Cathode (Triode 1)
  • 4 Heater (f)
  • 5 Heater (f)
  • 6 Anode (Triode 2)
  • 7 Grid (Triode 2)
  • 8 Cathode (Triode 2)
  • 9 Center Heater (f)

Application Notes

  • Heater operation: The tube can be operated with 6.3V or 12.6V, depending on the circuit design.
  • Grid resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable functionality.
  • Coupling capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high-frequency interference.
Old price: 22,90 €
Only 19,80 €
Sovtek 12AX7 / ECC83 LPS - Balanced
TT Selection: Balanced
Balanced gain on both systems


Very linear working 12AX7 / ECC83 with long anode plates and spiral heating, which makes the tube less sensitive to interference from AC heating.
We recommend this tube for audio and high-end amps as well as for "modern" Fender amps with more overdrive, but also as an input tube in old Marshall JCM800s.

Note: Tubes equipped with long plates are commonly associated with a "warmer" or "richer" sound, whereas those with shorter plates tend to deliver a "tighter sound". However, tubes featuring long plates exhibit increased sensitivity to vibrations and mechanical disturbances, rendering them less ideal for critical applications.
25,90 €
Tung-Sol 5751

Premium medium-Mu Twin Triode for use in preamplifier.

29,95 €
Tung-Sol 12AX7 / ECC83 Reissue
Premium high gain Twin Triode featuring ultra-low microphonics, and a big, warm and very musical soundstage. Performance surpassing NOS original in all areas.
23,90 €