Tube-Town GmbH

Output transformer for 5F6

• Pri.: 4200 Ohm C.T.                               
• Sec.: 0-4-8-16 Ohm
• Power: 50 Watt (28 Hz -3dB)
• Made in Europe

Files:

• Datasheet

• Core M6
• Primary: 120-230V-240V @ 50Hz
• Secondary HT and bias, 300V-50V-0-300V @ 300mA
• Secondary Heater: 3.15V-0-3.15V @ 6A

Files:

• Datasheet

Outputtransformer for Trainwreck Express projects

• Pri.: 6600 Ohm C.T.
• Sec.: 4-8-16 Ohm
• Power: 35 W (22Hz -3dB)

Files:

• Datasheet

Upgrade kit for the PoS100 with the following enhancements:     

• Selection of the adjustment range (Range): this effects the resolution of the load potentiometer. High initial damping allows easier fine tuning of the final volume. With a lower basic attenuation the adjustment range is wider and covers a larger volume spectrum     
• Selection of the control behavior (Log/Lin): depending on the amplifier, the control behavior of the load potentiometer can be adapted     
• The upgrade kit includes all components needed to update an existing PoS100 with these new features     

Please note: the schematic and layout plan for this kit will be sent by email together with the invoice, usually on the same day the order is sent.

Fender® style Footswitch

• 2-button
• Vintage style, black
• RCA-Plug
• ca. 3,5 m shielded wire
• labeled "vib" and "rev"

• Size (L x W): ca. 100 x 80 cm (only available in this size)
• Original Manufacturer
• Material: 100% treated paper
• Price per pcs.
• Actual shades may vary.

Further information and notes on Grillcloth

• FAQ Grillcloth

TT PX45 - a  PX18 in combination with the powerstage of the JTM45

Set of componentes for building the TT TT PX45 Guitar Amp.
Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Transformers
  • Power: tt-jtm45-pw
  • Output: tt-otjtm45D, Dual-Primary
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes (12AX7 / ECC83 and EL34)
• Fuses & Fuesholder

NOT INCLUDED:

• Headshell
• Chassis ch045
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

Faceplate for TT Amp-Kit PX45

• Farbe: #LG10 gold GLÄNZEND lackiert
• Material: 1.5 mm Acryl Revers
• Front + Rück Blende

Files:

• Template

TT Selection: V1 - Low Noise
This tube is selected for sensitive input stages (V1)

Tube-Town E83CC Preamp-Tube

High-quality 12AX7 / ECC83 / 7025 preamp tube with low background noise and reduced feedback tendency due to short anode plates, as well as a powerful bass and a dense sound. Very suitable for input stages with high amplification or amplifiers with generally high gain.
Dropin replacement for all 12AX7, ECC83, 7025, and E83CC tubes.

Electrical Characteristics

• Heater voltage (Uf): 6.3V or 12.6V
• Heater current (If): 300mA at 6.3V, 150mA at 12.6V
• Anode voltage (Ua): Maximum 300V
• Grid voltages (Ug1): -2V (typical)
• Grid voltages: -50V to 0V
• Anode current (Ia): 1.2mA (typical)
• Anode power dissipation: Maximum 1W per triode
• Anode resistance (ra): 62.5kΩ
• Amplification factor (μ): 100
• Transconductance (S): 1.6mA/V
• Input capacitance (Cin): 1.6pF
• Output capacitance (Cout): 1.6pF

Mechanical Characteristics

• Socket: B9A (Noval)
• Number of pins: 9

Pin Configuration

• 1 Anode (Triode 1)
• 2 Grid (Triode 1)
• 3 Cathode (Triode 1)
• 4 Heater (f)
• 5 Heater (f)
• 6 Anode (Triode 2)
• 7 Grid (Triode 2)
• 8 Cathode (Triode 2)
• 9 Center Heater (f)

Application Notes

• Heater operation: The tube can be operated with 6.3V or 12.6V, depending on the circuit design.
• Grid resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable functionality.
• Coupling capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high-frequency interference.

Mounting kit for all TT-Chassis which are designed for mounting with cagenuts and 19" housings

Included are:

• 4 x cagenut M6
• 4 x thread screw M6 x 30

• Tube-Town universal basic pcb for stomp-boxes
• Size: 77,5 x 54 mm
• Material: 1,6 mm FR3, blue

• Size: 25 x 64 mm
• One-side copper layer: 35 µ
• Material: FR2, 1,5 mm
• Grid: 2,54 mm
• Hole: Ø ca. 1 mm

TT 5F6 V2 Classic Amp Kit

Set of componentes for building the TT 5F6 V2 Guitar Amp.
Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Transformers (Power, Choke and Output)
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes
• Fuses & Fuesholder

NOT INCLUDED:

• Chassis ( see "Accessories" tab for matching chassis )
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

Tube-Town 5F6A Fender-Style Chassis

• Size: 508 x 126 x 67 mm
• Material: 1,5 mm Steel, hot-dip galvanized
• without silkscreen printing
• including capacitor cover
• cornerd welded
• Made in Germany

Files:

• Datasheet