Power Jack IEC320 / C14

• 80% PVC film
• 20% polyester-cotton fabric
• REACH compliant

waterbased Tolex-Glue, 500 ml

How To use ?
The glue must be applied onto the wood and the Tolex.
After a dyring time of ca. 30 min the Tolex can be put onto the wood.

And how much glue do you need ?
The can of 500 ml is enough for ca. 2.3 m². This is enough for a TTC212REX and there is still about 100 ml glue left.

Attention
For a better adhesive power it is recommended to put a second layer of glue onto the tolex after the drying time.

Files:

• Safety Datasheet

• 20 mm rubber foot black.
• Height: 9 mm.
• Fixing hole: 3,3 mm.
• Weight: 2,8g
• Pack of 4
• Screws included

• 8" (203 mm) steel basket diameter
• 20 watts, 4 ohm, 94 dB SPL
• 1" copper voice coil, Kraft paper former
• 10 oz ferrite magnet
• USA-made hemp cone
• Size, Nominal (inch & mm): 8" (203 mm)
• RoHS Compliant: Yes
• Nominal Impedance (Z) (Ω): 4
• Rated Power IEC268-5 (W): 20 Watts
• Rated Impedance (Ω): 4
• Continuous Power (W): 20
• Program Power (W): 40
• Frequency Range (Hz): 80 - 10,000
• Sensitivity (dB SPL) ¹: 94
• Resonant Frequency (Fs) (Hz): 139
• DC Resistance (Re) (Ω): 3.4
• Voice Coil Inductance (Le) (mH): 0.12
• Mechanical Q Factor (Qms): 15.36
• Electrical Q Factor (Qes): 4.45
• Total Q Factor (Qts): 3.45
• Mechanical Resistance (Rms) (kg/s): 0.47
• Compliance Equivalent Volume (Vas) (L): 10.92
• Suspension Compliance (Cms) (mm/N): 0.16
• Surface Area of Diaphragm (Sd) (cm²): 221.67
• Moving Mass (Mms) (gm): 8.28
• Magnetic Gap Height (mm): 6.0
• Coil Winding Height (mm): 6.35
• Motor Force Factor (BL) (T•M): 2.36
• Efficiency (η₀) (%): 0.64
• Efficiency Bandwidth Product (EBP) (Fs/Qes): 31.46
• Basket Type: Stamped steel with black powder coat
• Terminal Size (mm): 5.2 x 0.5
• Voice Coil Wire Material: Copper
• Voice Coil Former Material: Nomex
• Voice Coil Winding Style: Single Layer
• Magnet Material: Ferrite
• Magnet Weight (g): 283.5
• Cone Body Material: Hemp
• Dust Cap Material: Felt
• Spider Material: Cotton
• Net Weight (kg): 1.01

• up to T 70 °C
• with one fuse holders 5.0 x 20 mm
• Housing: polyamide
• UL 94 V-0, black
• for snap-on mounting
• Double-pole + protective ground 10 A/250 V
• single-pole fusing with bridge to the fuse holder at the L terminal
• fuse holder terminals for soldering
• Design to IEC/EN 60320-1
• fuse holder to IEC/EN 60127-6
• Certifications: ENEC, Semko, UL, CSA

• with one fuse holders 5.0 x 20 mm
• Housing: polyamide
• for panel mounting
• IEC320 / C14
• Double-pole + protective ground 10 A/250 V
• single-pole fusing with bridge to the fuse holder at the L terminal
• fuse holder terminals for soldering

Power Jack, Chassis mount

• Schurter 6162.0046
• Ratings IEC: 10 A / 250 VAC; 50 Hz
• Ratings UL/CSA: 15 A / 250 VAC; 60 Hz
• Dielectric Strength:    
  • > 3 kVAC between L-N
  • > 1.5 kVAC between L/N-PE (1 min/50 Hz)
• Allowable Operation Temp.:-25 °C to 70 °C
• Degree of Protection: from front side IP 20 acc. to IEC 60529
• Protection Class:Suitable for appliances with protection class 1 acc. to IEC 61140
• Material: Housing PA6, black, UL 94V-0