MOD Reverb Tank 8AB2A1B

The LNDVerb kit is based on a classic Fender reverb circuit, but uses LND 150 Mosfets instead of tubes. These can be operated at voltages as high as 500 V, to get as close as possible to the characteristics of real tubes.

The kit can be integrated into an existing amplifier or can be build as standalone unit like the Fender tube reverb.

The unit needs less than 10 mA current, so a VPump for example can be used as power supply in a standalone build. If it gets integrated into an existing amplifier the already present power supply of the amp can be used to supply the needed voltage for the unit without the need to upgrade the power transformer.

A reverb transformer of the type 125A20B or similar and a reverb tank are necessary to operate the LNDVerb. These are both not included in the kit.

The needed RCA phone sockets and potentiometers are included in the kit.

Further informations and examples of the finished unit can be found in the PDF below.

Matching parts are linked below and can be ordered with the unit if needed.

Files:

• Datasheet

 

Aluminium Knop black with diamond pattern

• Diameter: 12 mm
• High: 15,4 mm
• with set screw
• Shaft: for 6 mm shaft
• pack of one knob

• Material: Phenolic
• Shaft Size: 6  mm
• Size: 15 x 17,5 mm
• Mounting: Push on

• Type: Chickenhead
• Material: Phenolic
• Shaft Size: 6 - 6,3 mm
• Size: 32 x 13,7 mm
• Mounting: Set-Screw

• Mini, Layout Type B, Version 2020
• Size: 285 x 165 x 60 mm
• Mounting: with cage nuts (not included)
• Material: 2 mm Aluminium (AlMg3)
• Made in Germany
• Mounting: with cage nuts (not included)

Please note: The chassis may show traces and marks due to production.

Files:

• Datasheet V2020
• Datasheet V2013 (discontinued)

Set of componentes for building the TT Tube-Reverb.
Please visit the >>Project page for more infos about the amp.

INCLUDED:

• Mains Transformer for 120, 230 and 240V mains
• Outputtransformer
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switche
• PSU
• Tubes (1 x 12AX7, 1 x 12AT7,1 x JJ EL844)
• Fuses & Fuesholder

NOT INCLUDED:

• Knobs
• Chassis
• Faceplate
• REVERB TANK

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it than don't build it.

Lemberg 020 Headshell Flatpack
For all chassis of the LoW-Series WITHOUT side mounting brackets.
This flatpack is made of high quality, 15 mm birch multiplex, is completely CNC milled and drilled and very easy to assemble.

For the assembly you need

• Wood drill 5 mm
• Cross-head screwdriver or cordless screwdriver (recommended)
• Wood glue (NOT included in delivery)

The surface of the assembled headshell can be treated as desired. We recommend to oil it, because this is a very simple but effective procedure. However, it can also be painted or covered with Tolex (in which case the width of the front panel may need to be reduced) or otherwise treated.
Furthermore, corners, handles and rubber feet can be added according to your taste and need. Suitable accessories are listed in the accessories list under the product description here.

Files

• Assembly Instruction

Specifications

• Size (WxHxD): 318 x 190 x 215 mm (Outside)
• Hardware: Screws are included.
• Wood: 15 mm Birch Plywood

[content:3210136]

• Type: Footswitch
• Version: SPDT momentary OFF - (ON)
• max. Rating: 4A@125VAC / 2A@250VAC
• Drill Ø: 12 mm
• Termination Style: solder-lugs, 2 pins