Main page » Tubes » JJ-Electronic » JJ EL84 #08 - TT 18W, TT Spitfire, AC30

JJ EL84 #08 - TT 18W, TT Spitfire, AC30

Description

JJ EL84 #08 - Medium

recommended for TT 18W, TT Spitfire and AC30
Price for one tube.

FAQ: If I order two or more of these tubes, are they all "the same"?
Yes, the tubes are all "matched" and selected for the in the description mentioned amplifiers.
FAQ: Can I replace the tubes myself or are adjustments needed?
Adjustments are not possible on the listed amplifier (unless a bias potentiometer has been added afterwards). The replacement can therefore be done without adjustments.

Safety Information

Safety Information for Vacuum Tubes

For all electrical, electromechanical and mechanical components, the specifications and operating parameters arising from the respective type standard generally apply.
Further information, where available, can be found in the respective data sheets and product descriptions included with the product.

General Information

NOT SUITABLE FOR CHILDREN - choking hazard due to small parts
NOT SUITABLE FOR UNTRAINED PERSONS - danger to life due to high voltages
The safety and processing requirements applicable to the component must be observed
CE conformity applies only when installed professionally
Warranty becomes void in case of improper handling
The operator is responsible for proper installation
Local regulations and VDE provisions must be complied with
Never exceed the rated power
Never exceed the rated voltages and currents

Required Expertise

Use of measuring instruments (multimeter, oscilloscope) and evaluation of measurement results
Safe handling of high voltages (up to 500V and more)
Reading and understanding circuit diagrams
Selection of appropriate tools
Knowledge of electrical components and their characteristics
First-aid knowledge for electrical accidents
Knowledge of VDE regulations and safety requirements

Amplifier Tubes

Hazard due to high voltages
Hazard due to very high heat generation
Hazard due to glass breakage
Hazard due to UV radiation in case of defective tubes

Manufacturer

Herstellerinformationen | Manufacturer Information
JJ Electronic
A. Hlinku 3
022 01 ČADCA
Slowakische Republik
www.jj-electronic.com

Customer reviews

Essential information about customer reviews We do not verify that the published reviews come from such consumers who have actually used or purchased the rated goods or services. All reviews, i.e. positive and negative, are published. No reviews that are unobjective, offensive or unrelated to the product will be published.

Unfortunately there are no reviews yet. Be the first who rates this product.

Needed for:

JJ EL84 / 6BQ5 Red Label - QUARTETT

4 tubes, matched as quad

JJ EL84 / 6BQ5 Red Label

Files:

Datasheet

65,80 €
16,45 € per Piece

JJ EL84 / 6BQ5 Red Label - PAIR

2 tubes, matched as pair

JJ EL84 / 6BQ5 Red Label

Files:

Datasheet

32,90 €
16,45 € per Piece

Customers who bought this product bought also the following products:

TT E83CC (12AX7 / ECC83 / 7025) - V1

TT Selection: V1 - Low Noise
This tube is selected for sensitive input stages (V1)

Tube-Town E83CC Preamp-Tube

High-quality 12AX7 / ECC83 / 7025 preamp tube with low background noise and reduced feedback tendency due to short anode plates, as well as a powerful bass and a dense sound. Very suitable for input stages with high amplification or amplifiers with generally high gain.
Dropin replacement for all 12AX7, ECC83, 7025, and E83CC tubes.

Electrical Characteristics

Heater voltage (Uf): 6.3V or 12.6V
Heater current (If): 300mA at 6.3V, 150mA at 12.6V
Anode voltage (Ua): Maximum 300V
Grid voltages (Ug1): -2V (typical)
Grid voltages: -50V to 0V
Anode current (Ia): 1.2mA (typical)
Anode power dissipation: Maximum 1W per triode
Anode resistance (ra): 62.5kΩ
Amplification factor (μ): 100
Transconductance (S): 1.6mA/V
Input capacitance (Cin): 1.6pF
Output capacitance (Cout): 1.6pF

Mechanical Characteristics

Socket: B9A (Noval)
Number of pins: 9

Pin Configuration

1 Anode (Triode 1)
2 Grid (Triode 1)
3 Cathode (Triode 1)
4 Heater (f)
5 Heater (f)
6 Anode (Triode 2)
7 Grid (Triode 2)
8 Cathode (Triode 2)
9 Center Heater (f)

Application Notes

Heater operation: The tube can be operated with 6.3V or 12.6V, depending on the circuit design.
Grid resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable functionality.
Coupling capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high-frequency interference.

25,90 €