Tube-Town GmbH

• Insulation: Silicon
• Operation Voltage: 300 V AC / 500 V DC
• Test Voltage: 2000 V
• Operating temperatures:    –40 bis +180 °C
• Packing: 5 m
• Cross-Section: 0,25 mm²
• Outer Diameter: 1.6 mm
• Stranded wire structure: tinned copper

• Insulation: Silicon
• Operation Voltage: 300 V AC / 500 V DC
• Test Voltage: 2000 V
• Operating temperatures:    –40 bis +180 °C
• Packing: 5 m
• Cross-Section: 0,25 mm²
• Outer Diameter: 1.6 mm
• Stranded wire structure: tinned copper

• Insulation: Silicon
• Operation Voltage: 300 V AC / 500 V DC
• Test Voltage: 2000 V
• Operating temperatures:    –40 bis +180 °C
• Packing: 5 m
• Cross-Section: 0,25 mm²
• Outer Diameter: 1.6 mm
• Stranded wire structure: tinned copper

• Insulation: Silicon
• Operation Voltage: 300 V AC / 500 V DC
• Test Voltage: 2000 V
• Operating temperatures:    –40 bis +180 °C
• Packing: 5 m
• Cross-Section: 0,25 mm²
• Outer Diameter: 1.6 mm
• Stranded wire structure: tinned copper

• Insulation: Silicon
• Operation Voltage: 300 V AC / 500 V DC
• Test Voltage: 2000 V
• Operating temperatures:    –40 bis +180 °C
• Packing: 5 m
• Cross-Section: 0,25 mm²
• Outer Diameter: 1.6 mm
• Stranded wire structure: tinned copper

• Insulation: Silicon
• Operation Voltage: 300 V AC / 500 V DC
• Test Voltage: 2000 V
• Operating temperatures:    –40 bis +180 °C
• Packing: 5 m
• Cross-Section: 0,25 mm²
• Outer Diameter: 1.6 mm
• Stranded wire structure: tinned copper

• Signal wire Li2YDY 2 x 0,14 mm² 
• with single shielding and insulation
• Diameter Outside: ca. 3 x6 mm
• Voltage Rating: max. 50 / 75V AC/DC
• Temperature range: -30 bis +70 C°
• Conductor resistance: 135 Ohm / km @ 20 C°
• Insulation resistance: min. 20 MOHm x km @ 20 C°
• Length: 1 m

The TT Tonehound is a universal solution for home recording or recording in general. It consists of a reactive load and a speaker simulation. The Tonehound gets connected to a tube amp instead of a speaker, through the integrated cab-sim it can be connected to an audio interface, a recording station or a mixer console.

It is designed to handle up to 100 watts at 8 ohms. The used speaker simulation is our own, which is also available as a separate and independent kit.

The Cab-Sim offers:

• 6 different voicings
• balanced XLR output with switchable ground lift
• unbalanced output for 6,3 mm plugs
• headphone output for 6,3 mm stereo plugs
• switchable true bypass for the cab-sim, the outputs get true line outs
• adjustable output signal level

The kit includes all necessary parts for building the Tonehound like pcb, capacitors, resistors, coils, jacks, knobs, screws, wires and an aluminum chassis. The needed tools are a reasonable solder station, screw drivers, flat pliers, a countersink and a little craftsmanship.
Check the >>Project-Page for more pictures !

• Internal thread on both sides
• Thread size: M2.5
• Internal thread: 5 / 5 mm
• Material: galvanised steel
• Length: 10 mm

Internal thread on both sides

• Thread size: M2.5
• Internal thread: 6 / 6 mm
• Material: galvanised steel
• Length: 15 mm

Internal thread on both sides

Thread size: M2.5

Internal thread: 6 / 6 mm

Material: galvanised steel

Length: 20 mm

Internal thread on both sides

Thread size: M2.5

Internal thread: 6 / 6 mm

Material: galvanised steel

Length: 30 mm

Internal thread on both sides

Thread size: M2.5

Internal thread: 6 / 6 mm

Material: galvanised steel

Length: 25 mm

4 x Plastic Cabinet corner VOX® Style
incl. screws and nails

4 x Plastic Cabinet corner, front Marshall® Style
4 x Plastic Cabinet corner, back Marshall® Style
Internal radius: 25 mm

Tube-Town EZ-Board
for Fender 6G15 Reverb Unit
Size: 161 x 72 mm

The TT Tonehound is a universal solution for home recording or recording in general. It consists of a reactive load and a speaker simulation. The Tonehound gets connected to a tube amp instead of a speaker, through the integrated cab-sim it can be connected to an audio interface, a recording station or a mixer console.

It is designed to handle up to 100 watts at 16 ohms. The used speaker simulation is our own, which is also available as a separate and independent kit.

The Cab-Sim offers:

• 6 different voicings
• balanced XLR output with switchable ground lift
• unbalanced output for 6,3 mm plugs
• headphone output for 6,3 mm stereo plugs
• switchable true bypass for the cab-sim, the outputs get true line outs
• adjustable output signal level

The kit includes all necessary parts for building the Tonehound like pcb, capacitors, resistors, coils, jacks, knobs, screws, wires and an aluminum chassis. The needed tools are a reasonable solder station, screw drivers, flat pliers, a countersink and a little craftsmanship.
Check the >>Project-Page for more pictures !

Size: 210 x 150 x 120 mm