Main page » Components » Cables + Wires » Wires for Speakers » Wiring Harness, mono, speaker crimps

Wiring Harness, mono, speaker crimps

Description

Wiring Harness, mono, speaker crimps
Wire: 2 x 1,5 mm² red - black
Speaker Crimps on both sides
Length: ca. 55 cm

Information about the manufacturer

Herstellerinformationen | Manufacturer Information

Tube-Town GmbH
Rumbergring 37
D-66969 Lemberg
eMail: info@tube-town.de

Customer reviews

Essential information about customer reviews We do not verify that the published reviews come from such consumers who have actually used or purchased the rated goods or services. All reviews, i.e. positive and negative, are published. No reviews that are unobjective, offensive or unrelated to the product will be published.

Unfortunately there are no review yet. Be the first who rate this product.

Needed for:

WGS Veteran 30 12" / 60 W / 16 Ohm

The 12” Veteran 30™ speaker from WGS is tonally superior to Celestion's™ Vintage 30™ speaker. The tonal improvement is in the upper-mids. The Veteran 30™ speaker has smoothed out the upper-mid "spike" notorious in the Vintage 30™ speaker.

Unit Weight: 10 pounds

Mounting Information

Diameter:12.2”
Overall depth: 5.3”
Cut-out diameter: 11.1”
Mounting slot dimensions: 0.31”
Number of mounting slots: 8

Thiele-Small Parameters

Resonant Frequency (Fs): 94.84 Hz
DC Resistance (Re): 7.99 Ohm
Coil Inductance (Le): 0.35 mH
Mechanical Q (Qms): 12.15
Electromagnetic Q (Qes): 0.78
Total Q (Qts): 0.74
Compliance Equiv. Vol. (Vas): 18.53 cu ft
Mech. Compliance of Susp. (Cms): 0.10 mm/N
BL Product (BL): 13.25 T-M
Diaphragm Mass Inc. Airload (Mms): 28.88 grams
Surface Area of Cone (Sd): 366.10 cm squared
Sound Pressure Level (spl): 99.84 db

129,00 €

Jensen C10Q - 8 Ohms

CERAMIC Vintage

The JENSEN® "C" series speakers were developed because the world's supply of cobal (Co in AlNiCo) slump, making this raw material more expensive. While ceramic magnets are larger in size than comparable AlNiCo magnets of the same gauss strenght, their cost is lower. "C" series JENSEN® speakers use same cones and voice coils comparable to our AlNiCo series speakers, thus providing a similar tone but at a reduced price.

Technical Details:

Size: 10"
Impedance: 8 Ohm
Rated Power (RMS): 35 W
Sensitivity @ 1 W, 1 m: 95,2 dB
Resonance Frequency fs: 96 Hz

Files:

Datasheet

78,00 €

Jensen Jet Blackbird 12" / 100 W / 16 Ohm

Great dynamics, very rich harmonic texture, plenty of warmth, sparkling highs. Warm, smooth and distortion-friendly tone. Deep, fat low end, open, burnished mids and airy, silvery highs. Firm, authoritative and solid, handles well overdrive, bringing out colorful details and holding strong even at maximum distortion. Good definition with lots of high gain. Full-bodied and detailed with clean tones.
Versatile, successfully merging modern and vintage flavours. Can be used in small combos, for very clean, warm sound, and in powerful amps, for well controlled break-up.

Technical Details:

Size: 12"
Impedance: 16 Ohm
Rated Power (RMS): 100 W
Sensitivity @ 1 W, 1 m: 98 dB
Resonance Frequency fs: 95,1 Hz

Files:

249,00 €

Celestion G10 Creamback 10" / 45W / 8 Ohm - MADE IN UK

The new G10 Creamback packs everything guitar players love about Creamback speakers into a 10-inch format. Hand-built in the UK using the same production methods and materials developed for the 12-inch models, the G10 Creamback uses a ceramic magnet and a 1.75-inch voice coil to deliver 45-watt power handling. With all the punch and dynamics typical of a 10, its overall tone is warm, expressive, detailed and well-balanced.

General Specifications

Nominal diameter: 10", 254mm
Power rating: 45W Nominal
Impedance: 8Ω
Sensitivity: 96dB
Chassis type: Pressed steel
Voice coil diameter: 1.75", 44.5mm
Voice coil material: Round copper
Magnet type: Ceramic
Magnet weight: 14oz
Frequency range: 95-5500Hz
Resonance frequency, Fs: 98Hz
DC resistance, Re: 6.4Ω

Mounting Information

Cut-out diameter: 9.0", 229mm
Diameter: 10.0", 254mm
Magnet structure diameter: 4.9", 124mm
Mounting slot dimensions: 0.25 x 0.43", 6.5 x 11mm Ø
Mounting slot PCD: 9.6", 245mm
Number of mounting slots: 8
Overall depth: 4.0", 102mm
Unit weight: 3.5lb, 1.6kg

125,00 €

WGS G12Q 12" / 20 W / 8 Ohm

Building on the popularity of our G12C, we developed the G12Q for those times when you want the speaker to add some natural, vintage breakup but maintain clarity. With a 20 oz magnet and a 1" voicecoil, the G12Q definitely has a vintage American flavor. We highly recommend it with 5E3 style circuits.

Thiele-Small Parameters

Resonant Frequency (Fs):91.91 Hz
DC Resistance (Re): 7.70 Ohm
Coil Inductance (Le): 0.26 mH
Mechanical Q (Qms): 20.75
Electromagnetic Q (Qes): 2.64
Total Q (Qts): 2.35
Compliance Equiv. Vol. (Vas): 22.17 cu ft
Mech. Compliance of Susp. (Cms): 0.12 mm/N
BL Product (BL): 6.57 T-M
Diaphragm Mass Inc. Airload (Mms): 25.71 grams
Surface Area of Cone (Sd): 366.10 cm squared
Sound Pressure Level (spl): 95.92 db

89,00 €

Jensen C12R 8 Ohms

CERAMIC Vintage

Technical Details:

Size: 12"
Impedance: 8 Ohm
Rated Power (RMS): 25 W
Sensitivity @ 1 W, 1 m: 93,8 dB
Resonance Frequency fs: 74,0 Hz

Files:

Datasheet

65,00 €

Celestion Gold 12" / 50 W / 8 Ohm - MADE IN UK

Building on the platform of the Blue the Gold is a higher-powered Alnico-magnet guitar speaker that recreates the unmistakable sonic signature of a ‘well played-in’ original.
Over time the high frequencies of a Blue soften and become less chalky as the cone becomes more flexible – a much sought after characteristic that the Gold exhibits straight out of the box.

Also present in the Gold sound from the outset is an added warmth and complexity in the midrange which coupled with the classic Alnico qualities of a laid-back attack rounded low end and brilliant bell-like highs deliver huge rhythm voicings and saturated vocal lead tones.
The Gold is a wonderfully expressive and revealing loudspeaker affording guitarists an unprecedented degree of dynamic control.

Specifications

Nominal diameter 305mm / 12in
Power rating 50W
Rated impedance 8Ω or 15Ω
Sensitivity 100dB
Chassis type Pressed steel
Magnet type Alnico
Voice coil diameter 1.75in / 44.5mm
Voice coil material Round copper
Frequency range 75-5000Hz
Resonance frequency, Fs 75Hz
DC resistance, Re 6.4Ω or 11.8Ω

Mounting Information

Cut-out diameter 283mm / 11.1in
Diameter 309mm / 12.2in
Magnet structure diameter 128mm / 5.0in
Mounting hole dimensions 7.9mm / 0.31in Ø
Mounting hole PCD 297mm / 11.7in
Number of mounting holes 4
Chassis depth (inc gasket) 92mm / 3.63in
Magnet depth 73mm / 2.87in
Overall depth 165mm / 6.5in
Unit weight 4.2kg / 9.3lb

279,00 €

Jensen C8R - 4 Ohm

CERAMIC Vintage

Technical Details:

Size: 8"
Impedance: 4 Ohm
Rated Power (RMS): 25 W
Sensitivity @ 1 W, 1 m: 92,7 dB
Resonance Frequency fs: 125 Hz

Files:

Datasheet

60,00 €

Jensen P12R - 12" / 25 W / 16 Ohms

The "Living legends" of Rock and Roll guitar sounds are back! Original designs of the late 40's and early 50's have been recreated using many of the original parts suppliers. Highly efficient AlNiCo magnets and seamed paper cones are the foundation for the famous JENSEN® Sound. JENSEN® "P" Series Vintage AlNiCo magnet speakers represent an important contribution to the paste, present and, no doubt, the future of rock and roll music. They are loved by generations of guitarists around the world.

Technical Details:

Size: 12"
Impedance: 16 Ohm
Rated Power (RMS): 25 W
Sensitivity @ 1 W, 1 m: 95 dB
Resonance Frequency fs: 80 Hz
Bell: No Bell

Files:

Datasheet

120,00 €

Terminal Mono/Stereo - Marshall Replacement

Universal Mono/Stereo Terminal, replacement for Marshall Terminal ME-19605000 which is used in 2X12 or 4X12 Marshall speaker cabs, with extended connections and possibilities. For the used with a 4X12 a second wireset is needed to connect two speakers in parallel. Please see the list with recommended products.

If used with this speakers

2 x 8 Ohms or
4 x 16 Ohms or
4 x 4 Ohm

one will get the following connection options

4 ohm mono
8 ohm left + 8 ohm right stereo
8 ohm left only mono
8 ohm right only mono
16 ohm mono

Colorcodes:

black: L-
red: L +
green: R -
white: R +

Files:

Datasheet

28,00 €

Celestion Peacekeeper - 12" / 50 W / 8 Ohm - 86 dB - NEU

The Peacekeeper is a revolutionary new attenuating speaker for guitarists from Celestion. It’s the simplest and most toneful way of being able to dial your amplifier right up to its “sweet spot”, while keeping the decibel levels down.

Featuring a unique dual voice coil design, this attenuating speaker works together with an amp, like a conventional guitar speaker, only with significantly reduced output sensitivity. Enabling you to drive your amplifier harder while still listening at reasonable volume levels. Load it into your cab and the Peacekeeper will attenuate your amplifier in the most natural way possible, with zero additional colouration or tonal compromise.

General Specifications

Nominal diameter: 12", 305mm
Power rating: 50 Wrms
Nominal impedance: Available 8Ω
Sensitivity: 86 dB
Chassis type: Pressed steel
Voice coil material: Round copper
Magnet type: Ceramic
Magnet weight: 50oz, 1.42kg
Frequency range: 70-5000Hz
Resonance frequency, Fs: 80Hz

Mounting Information

Cut-out diameter: 11.1", 283mm
Diameter: 12.2", 309mm
Magnet structure diameter: 6.1", 156mm
Mounting slot dimensions: 0.31", 7.9mm Ø
Mounting slot PCD: 11.7", 297mm
Number of mounting slots: 4
Overall depth: 5.3", 135mm
Unit weight: 10.6lb, 4.8kg

239,00 €

WGS 12L 12" / 200 W / 8 Ohm

Headroom, clarity, balanced response, power...
These terms have become synonymous with a vintage American design that is known and sought the world over. WGS now pays tribute to this classic with our WGS12L. However like all of our designs, we didn't set out to make a clone. With this model we paid extra special attention to the details, producing a speaker that delivers that same even response without sounding sterile and lifeless. Boasting a cast frame, 2.5" voice coil and a 200 watt rating, and clocking in at 18 pounds, this beast is loaded for bear. As a welcome addition to the WGS fleet, this speaker is definitely our battleship.

Note from the boss: "We compared both the EVM 12L and the WGS 12L in an 806 cabinet and it was almost impossible to tell them apart. The WGS 12L is a great alternative to the original and we recommend it without reservation as a perfect replacement for the EVM 12L."

Thiele-Small Parameters

Resonant Frequency (Fs): 49.58 Hz
DC Resistance (Re): 5.84 Ohm
Coil Inductance (Le): 0.35 mH
Mechanical Q (Qms): 7.41
Electromagnetic Q (Qes): 0.25
Total Q (Qts): 0.24
Compliance Equiv. Vol. (Vas): 50.51 cu ft
Mech. Compliance of Susp. (Cms): 0.27 mm/N
BL Product (BL): 16.74 T-M
Diaphragm Mass Inc. Airload (Mms): 38.77 grams
Surface Area of Cone (Sd): 366.10 cm squared
Sound Pressure Level (spl): 99.67 db

249,00 €

Jensen Bass Punch BP15/250 - 15" / 250 W / 8 Ohm

Punch Sound speakers offer great dynamics and super-fast response, giving the player an extremely solid bass sound.
Equipped with ferrite magnets and steel baskets, they are ideal for classic styles where a clean, tight and bright sound is required.

Specifications

Nominal Diameter: 385 mm / 15 in
Nominal Impedance: 8 Ω
Rated Power AES: 250 W
Continuos Program Power: 500 W
Sensitivity @ 1W/1m: 96.7 dB
Voice Coil Diameter: 65 mm (2.5")
Voice Coil Winding Depth: 13 mm
Magnetic Gap Depth: 8 mm
Flux Density: 1.15 T
Magnet Weight: 1450 g
Net Weight: 5.4 Kg
Magnet Type: Ferrite
Basket Material: Pressed Sheet Steel
Voice Coil Winding Material: Copper
Voice Coil Former Material: Aluminium
Cone Material: Paper
Cone Treatment: No
Surround Material: Treated Cloth
Dust Dome Material: Solid Paper

Thiele & Small Parameters

Re: 6.60 Ω
Qms: 4.26
Qts:0.51
Cms: 164 µm/N
Vas: 133.1 l
X max: +/- 3.4 mm
N: 2.30 %
Fs: 47.0 Hz
Qes: 0.57
Mms: 69.7 g
Bxl: 15.31 Tm
Sd: 754.8 cm²
X var: +/- 7.0 mm
Le (1KHz): 1.07 mH

165,00 €

Jensen Bass Punch BP10/150 - 10" / 150 W / 8 Ohm

Specifications

Nominal Diameter 266mm (10")
Nominal Impedance 8Ω
Rated Power AES 150W
Continuous Program Power 300W
Sensitivity @ 1W/1m 96.0dB
Voice Coil Diameter 50mm (2")
Voice Coil Winding Depth 11mm
Magnetic Gap Depth 8mm
Flux Density 1.20T
Magnet Weight 1100g
Net Weight 3.5kg

Thiele & Small Parameters

Re 6.10Ω
Fs 55.0Hz
Qms 5.93
Qes 0.35
Qts 0.33
Mms 30.7g
Cms 276μm/N
Bxl 13.48Tm
Vas 42.6l
Sd 330.1cm2
X max +/-2.4mm
X var +/-3.5mm
η0 1.87%
Le (1kHz) 0.85mH

107,00 €

Celestion A-Type - 12" / 50 W / 8 Ohm

Celestion guitar speakers have been an important part of British guitar tone since the birth of Rock & Roll.
Traditionally they’re known for lively and vocal midrange character with plenty of sparkle and chime which turns into an exciting growl when overdriven often compressing when pushed hard.
Inspired by our favourite modern American tones the A-Type is a different kind of guitar speaker from Celestion.
Of course it still has the musical and revealing three- dimensional quality that is the heart and soul of a Celestion guitar speaker however it
features a more laid-back midrange which reveals body and complexity in the upper register accompanied by full and rounded low frequencies.

The A-Type conveys a fluid even performance with an increased headroom threshold that allows your amp’s tone to shine through.
Clean players will love the smooth articulation; for rockers the brooding powerful low end threatens thunder that’s only a heavy riff away!

Specifications

Nominal diameter 305mm / 12in
Power rating 50W
Rated impedance 8Ω or 16Ω
Sensitivity 98dB
Chassis type Pressed steel
Magnet type Ceramic
Magnet weight 0.99kg / 35oz
Voice coil diameter 1.75in / 44mm
Voice coil material Round copper
Frequency range 75-5000Hz
Resonance frequency, Fs 75Hz
DC resistance, Re 6.2Ω&12.7Ω

Mounting Information

Cut-out diameter 283mm / 11.1in
Diameter 309mm / 12.2in
Magnet structure diameter 145mm / 5.7in
Mounting hole dimensions 7.9mm / 0.31in Ø
Mounting hole PCD297mm / 11.7in
Number of mounting holes 8
Chassis depth (inc gasket) 94mm / 3.70in
Magnet depth 33mm / 1.30in
Overall depth 130mm / 5.1in
Unit weight 3.5kg / 7.7lb

109,00 €

Celestion Bass PULSE 10 10" / 200 W / 8 Ohm

PULSE10
With its robust steel-chassis, PULSE10, provides a rock-solid bass performancewhether alone in a single speaker combo, in a 4x10 or even an 8x10 cab. Expecta tight, punchy low end with a warm mid-range that’s full of presence, bringingfocus and articulation to your playing. This heavy-duty driver truly delivers bassyou can feel as well as hear.

General Specifications

Nominal diameter: 10", 254mm
Power rating: 200W
Nominal impedance: 8Ω
Sensitivity: 94dB
Magnet type: Ferrite
Voice coil diameter: 2", 50.8mm
Coil material: Copper
Cone material: Kevlar loaded paper
Former material: Polyimide
Surround material: Cloth-sealed
Frequency range: 45-3500Hz
Xmax: 0.15", 4mm
Gap depth: 0.31", 8mm
Voice coil winding width: 0.62", 16mm

Small Signal Parameters

D: 0.21m/8.3in
Fs: 68Hz
Mms: 32.9g/1.16oz
Qms: 2.54
Qes: 0.53
Mmd: 29.26g/1.03oz
Qts: 0.44
Re: 6.03Ω
Vas: 25.8lt/0.91cu.ft.
BI: 12.88Tm
Cms: 0.15mm/N
Rms: 5.79kg/s
Le (at 1kHz): 0.92mH

Mounting Information

Cut-out diameter: 9", 229mm
Diameter: 10.1", 256mm
Mounting slot dimensions: 0.24x0.31", 6x8mm Ø
Mounting slot PCD: 9.6", 245mm
Number of mounting slots: 4
Overall depth: 4.3", 110mm
Unit weight: 6.6lb, 3kg

89,00 €

Customers who bought this product bought also the following products:

TTC 112 Lemberg BA - 1 x 12" - Flatpack

The ideal speaker cabinet for the DIY guitarist!
All parts CNC milled and drilled from high quality birch plywood for easy assembly at home or as a base for your own creations.

Size based on the very popular 112AM Lemberg:

Width: 500 mm
Height: 410 mm
Depth: 240 mm
Speaker cutout: 12"
Material: 15 mm birch plywood housing, 12 mm birch plywood baffle

The kit includes all components to build the speaker box according to standard as per documentation, such as: