Tube-Town GmbH

Width approx. 135 cm
Price per running meter
Color reproduction depends on the computer monitor and may vary
Supplied as one continuous piece when ordering more than 1 m

Material:

• 80% PVC film
• 20% polyester-cotton fabric
• REACH compliant

Please note!
When ordering more than 1 m of Tolex and selecting Deutsche Post / DHL Paket or Express as the shipping method, the Tolex will be cut to a width of approx. 115 cm. This is due to the maximum permitted parcel length of 120 cm for these shipping services.
To receive the full roll width, GLS or ExprexxXL must be selected as the shipping method.

Size of sample ca: 9 x 9 cm
Actual shades may vary.

Material:
80% PVC Film
20% Poly-Cotton Fibre

REACH compliant

Size of sample ca: 9 x 9 cm
Actual shades may vary.

Material:
80% PVC Film
20% Poly-Cotton Fibre

REACH compliant

B-STOCK: with flaws in the fabric

Fender Style Grillcloth in white. To get the best results with this grillcloth you should not color the baffle black.
Same texture and material as the Fender Cloth

• Size: ca. 60 x 90 cm (only available in this size)
• Fender Style
• Material: 100% Polypropylen
• Price per pcs.
• Actual shades may vary.

Further information and notes on Grillcloth

• FAQ Grillcloth

Transply, raw material
if you want to engrave by yourself

• Material: 1,5 mm Transply
• Size: 600 x 150 mm
• Colors: silver gold
• Engraving: black

NF Signal wire LiYDY 2 x 0,14 mm² shielded

• Diameter Outside: ca. 4 mm
• Voltage Rating max. 250 V
• Temperature range: -10 bis +70 C°
• Conductor resistance: 135 Ohm / km @ 20 C°
• Insulation resistance: min. 20 MOHm x km @ 20 C°
• Length: 5m

Mains transformer for Leslie 122/147 US-Model
for conversion of a 117 V Leslie to 230 V
This transformer should generally fit on all Leslie chassis produced for the US-market.
However, we recommend verifying the dimensions before purchase for added assurance.

• Core material M6
• Pri:0-117V-230V @ 50Hz
• Sec HT: 345V @ 400 mA
• Sec Heater: 6.3V @ 5 A
• EI 84 format (70 x 84 mm h=55 mm)

Dateien:

• Datasheet

With a soft and detailed sound, as well as sufficient headroom, the TT 12AU7/ECC82 enhances the sound characteristics of any amplifier, whether it's for guitar, bass, or high-end. These tubes deliver a dynamic range, captivating listeners and musician with uncompromising clean sounds and rich overdrive.

Features:

• Detailed sound
• Ideal for both low and high gain amplifiers

Tip:
Often, 12AU7 and 12AT7 types are used instead of 12AX7 tubes to either reduce the overall power of the amplifier or to just reduce the overloading of the preamp. In comparison to a 12AX7, the 12AU7 brings about a very large sonic difference, typically much greater than switching from 12AX7 to 5751 or 12AT7.

When using a 12AU7 in a driver stage normally designed for 12AX7, the overall power of the power stage is usually reduced. The extent of this difference depends on the amplifier or circuit. For example, a Marshall amplifier with a 12AX7 in the PI stage set at volume 5 will then reach the same volume level with a 12AU7 at volume 6 (perceived volume, not measured).

Electrical Properties

• Heater Voltage (Uf): 6.3V or 12.6V
• Heater Current (If): 300mA at 6.3V, 150mA at 12.6V
• Anode Voltage (Ua): Maximum 300V
• Grid Voltage (Ug1): -8.5V (typical)
• Anode Current (Ia): 10.5mA (typical)
• Anode Dissipation: Maximum 2.75W per triode
• Anode Resistance (ra): 7.7kΩ
• Amplification Factor (μ): 17
• Transconductance (S): 2.2mA/V
• Input Capacitance (Cin): 1.6pF
• Output Capacitance (Cout): 1.6pF

Mechanical Properties

• Socket: B9A (Noval)
• Number of Pins: 9

Pin Configuration

• 1 Anode (Triode 1)
• 2 Grid (Triode 1)
• 3 Cathode (Triode 1)
• 4 Heater (f)
• 5 Heater (f)
• 6 Anode (Triode 2)
• 7 Grid (Triode 2)
• 8 Cathode (Triode 2)
• 9 Center Heater (f)

Application Notes

• Heater Operation: The tube can be operated at 6.3V or 12.6V, depending on the circuit design.
• Grid Resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable operation.
• Coupling Capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high-frequency interference.

Flat Cable-Plug, Cable Shoe, crimp connection for width max 5,2 x 0,5 mm

• not insulated
• Conductor cross section: 1.0 to 2.5 mm²
• AWG conductor cross section AWG 17 to 14
• Brass, tin-plated
• Pack of 10 pcs