Tube-Town GmbH

Faceplate for TT Kit Surfmate

• Color: #C01 black / white
• Material: 1.5 mm Transply
• Front and rear panel

Files:

• Template

Kit TT PSU Mini Center Tap

Standard power supply for power transformers with center tap. NOT recommended for tube rectifiers because the first stage has a capacity of 100 µF which is too much for most tube rectifiers. Some capacitors need to get changed if it should be used with a tube rectifier (further informations in the datasheet).

The kit includes all components except a power transformer and a choke for building a PSU for tube amps. If you want to use a choke instead of the included 5 W resistor you must order the choke separately. The PSU is recommended for tube amps up to 50 Watt. The size of the PSU is only 97 x 55 mm and it has a height of ca. 40 mm (without spacer bolts).

Please refer to the attached schematic for more informations about the layout and design of the PSU.

Tip: use Duncanamps' PSU Designer to simulate and calculate power supplies.

Files:

• Datasheet

• RCA Phono socket gold plated with Teflon insulation
• 1 x black
• 1 x red
• 1 x white
• 1 x yellow
• Installation diameter: 6 mm

• Original 6K6
• NOS
• Mixed Brands
• not matched

• Single Relais PCB for channel switching etc..
• Size: 41 x 35 mm
• For the use with Finder Relais type 30.22.9xx  (or relais with similar pin layout).

• Grillcloth Sample
• Material: 94 % Polypropylen, 6 % Acrylic
• Size ca. 10 x 10 cm
• Actual shades may vary.

• Faceplate for TT Kit BFlex
• Color: #C14 silver / black
• Material: 1.5 mm Transply
• Set includes front and rear Panel

Files:

• Template

Power Supply chassis Socket,  with break contact and solder eyes, for front side mounting

• Diameter opening: 6,3 mm
• Diameter center pin: 1,9 mm
• Mounting hole: 11,8 mm
• Rated current: 0,5 A @ 12 V DC
• Isulation resistance: > 100 M Ohm

Marshall® Style 18W Amp kit, Point-to-Point, TMB Model

Set of componentes for building the TT 18W TMB Guitar Amp.
Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Transformers (Power and Output, tt-ma18pw-INT and Hammond 1750PA)
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes
• Fuses & Fuesholder

NOT INCLUDED:

• Chassis - please order the chassis which you want. The chassis tt-ch024 should be used for a head version of the amp and the chassis tt-ch026 for a combo build.
• Knobs
• Faceplate

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

TT EL84 / 6BQ5 #05 - Fender Blues Junior

• Not so hot than the #06 selection but still nice punch
• Recommended for Fender Blues Junior and Pro Junior and similar amps.
• Price for one tube.

FAQ: If I order two or more of these tubes, are they all "the same"?
Yes, the tubes are all "matched" and selected for the in the description mentioned amplifier.
FAQ: Can I replace the tubes myself or are adjustments needed?
Adjustments are not possible on the listed amplifier (unless a bias potentiometer has been added afterwards). The replacement can therefore be done without adjustments.

• Hexagon spacer bolts
• inner thread - outer thread
• Thread size: M3
• Internal thread: 7,5 mm
• External thread: 8 mm
• Material: polyamide
• Length: 20 mm
• Colour: black

• Hexagon spacer bolts
• inner thread - outer thread
• Thread size: M3
• Internal thread: 7,5 mm
• External thread: 8 mm
• Material: polyamide
• Length: 15 mm
• Colour: black

• Hiwatt style heat shield
• Size: approx. W=255 mm h= 125 mm
• Material: 1.5 mm aluminum

Signal lamp round, red

• Operating voltage: 230 V~
• Power: 0,05 W
• Light/housing color: red
• Connection: soldering lugs
• Installation Ø: 10 mm
• Installation depth: 35 mm
• Overall dimensions (ØxL): 12x42 mm