Speaker cable, 2 x 6,3 mm plug, 3 m

The Liverpool 1275 is the classic British rock tone,inspired by tones from the 80’s. A complex, thick and vocal midrange cuts through the upper-register, while nice, full, lower-mid grunt completes the warm, gutsy, tight lows. The highs, while clear, open and articulate remain warm and ear pleasing.

Spezification:

• Nominal Impedance (Z): 16 Ohm
• Rated Power IEC268-5: 75 Watt
• Sensitivity (@1W/1 m): 100 dB/SPL
• Frequency range: 75 – 5000 Hz
• Resonant Frequency (Fs): 83 Hz
• Voice Coil Diameter: 1,75"

Files:

• Datasheet

Finally, the wait is over. We have created a 10" speaker that captures all the tone and mojo of our extremely popular 12" Green Beret.   The Green Beret 10 boasts the same midrange push, articulate top end and warm, harmonically rich breakup of its larger namesake.  It also sports an impressive amount of low end for a 10" speaker.   With a 1.5" voice coil and a paper former, this speaker drips with vintage tone.    If you've been looking for classic British tone in a 10" speaker the Green Beret 10 delivers.

Tube-Town Review: Due to the smooth cone used in the 10" WGS Green Beret, its top end is much more subtle compared to the original 12" Celestion Greenback G12M, but also to the 10" Celestion Greenback. However, the midrange is not overemphasized and the whole speaker sounds full and balanced, with a distinct "American touch" to the overall sound.
We recommend the 10" Green Beret for everything from blues to rock to modern metal, but less so for blackface-typical clean sounds, for which there are better suited 10" speakers. In order for the speaker to develop its full sonic spectrum, it should be used either in an open cabinet or combo, or in a large-volume closed cabinet. A closed cabinet that is too small will dampen the speaker too much and cut the sound.
The WGS 10" Green Beret is also a real upgrade for many budget combos that are equipped with inexpensive 10" speakers and often sound a bit thin and sharp, especially when it comes to harder tones.

Thiele-Small Parameters (8 ohm version)

• Resonant Frequency (Fs): 117.31 Hz
• DC Resistance (Re): 6.8 Ohm
• Coil Inductance (Le): mH
• Mechanical Q (Qms): 9.429
• Electromagnetic Q (Qes): 1.884
• Total Q (Qts): 1.57
• Compliance Equiv. Vol. (Vas): 15.59 cu ft
• Mech. Compliance of Susp. (Cms): 0.082 mm/N
• BL Product (BL): 11.71 T-M
• Diaphragm Mass Inc. Airload (Mms): 22.4417 grams
• Surface Area of Cone (Sd): 336.0962 cm squared
• Sound Pressure Level (spl): 96.62 db

Vintage American Ceramic Guitar Speaker
8″ seamed ribbed cone with small ceramic motor, replacement for Jensen C8R.

• Small Ceramic Magnet
• Power: 15 W
• Sensitivity: 94,5dB
• Weight: 1,2 kg
• VC Diameter: 1″
• 8 Ohm
• Paper Coil

Designed to provide a fully immersive experience. These versatile drivers project robust warmth, detail, and clarity throughout their generous voicing. Single notes are thick with dense musicality while chords ring with exceptional definition. A perfect pairing with down-tuned guitars and high gain.
Build with a 55 Hz UK Made Kurt Mueller Cone

The 12” Reaper™ guitar speaker is a DROP IN REPLACEMENT for Celestion™ G12H30 Anniversary Edition. This speaker sounds like a Green Beret on steroids. Cone breakup does not occur as early as the Green Beret. This speaker sounds great mixed with a Green Beret, Veteran 30, or by itself.

Unit Weight:  10 pounds

Mounting Information

• Diameter: 12.2”
• Overall depth: 5.3”
• Cut-out diameter: 11.1”
• Mounting slot dimensions: 0.31”
• Number of mounting slots: 8

Thiele-Small Parameters

• Resonant Frequency (Fs): 126.60 Hz
• DC Resistance (Re): 8.20 Ohm
• Coil Inductance (Le): 0.33 mH
• Mechanical Q (Qms): 8.56
• Electromagnetic Q (Qes): 1.01
• Total Q (Qts): 0.90
• Compliance Equiv. Vol. (Vas): 10.52 cu ft
• Mech. Compliance of Susp. (Cms): 0.06 mm/N
• BL Product (BL): 13.58 T-M
• Diaphragm Mass Inc. Airload (Mms): 28.57 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.04 db

Vintage American Ceramic Guitar Speaker
12" seamed cone with Large Ceramic Magnet, upgrade replacement for Jensen C12N.

• Magnet:  Large Ceramic
• Power: 50 W
• Sensitivity: 99,5 dB
• Weight: 3,4 kgs
• VC Diameter: 1.5″
• 16 Ohm

The 12” Reaper™ guitar speaker is a DROP IN REPLACEMENT for Celestion™ G12H30 Anniversary Edition.
This speaker sounds like a Green Beret on steroids.
Cone breakup does not occur as early as the Green Beret.
This speaker sounds great mixed with a Green Beret, Veteran 30, or by itself.

Unit Weight:  10 pounds

Mounting Information

• Diameter: 12.2”
• Overall depth: 5.3”
• Cut-out diameter: 11.1”
• Mounting slot dimensions: 0.31”
• Number of mounting slots: 8

Thiele-Small Parameters

• Resonant Frequency (Fs): 126.60 Hz
• DC Resistance (Re): 8.20 Ohm
• Coil Inductance (Le): 0.33 mH
• Mechanical Q (Qms): 8.56
• Electromagnetic Q (Qes): 1.01
• Total Q (Qts): 0.90
• Compliance Equiv. Vol. (Vas): 10.52 cu ft
• Mech. Compliance of Susp. (Cms): 0.06 mm/N
• BL Product (BL): 13.58 T-M
• Diaphragm Mass Inc. Airload (Mms): 28.57 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.04 db

The ET10 is the 10” version of one of our most popular speakers: the ET65. The ET10 boasts a tone reminiscent of its 12” counterpart, but with a bit more of a pronounced midrange. The low end from this 10 is surprisingly heady, but remains tight in all situations. Top it off with a smooth but articulate top end, and you have one of the most highly anticipated ten inch speakers to date.

Unit Weight: 6 lbs

Thiele-Small Parameters

• Resonant Frequency (Fs): 113.32 Hz
• DC Resistance (Re): 6.626 Ohm
• Coil Inductance (Le): 0.16 mH
• Mechanical Q (Qms): 6.72
• Electromagnetic Q (Qes): 0.72
• Total Q (Qts): 0.65
• Compliance Equiv. Vol. (Vas): 17.06 cu ft
• Mech. Compliance of Susp. (Cms): 0.11 mm/N
• BL Product (BL): 10.63 T-M
• Diaphragm Mass Inc. Airload (Mms): 17.25 grams
• Surface Area of Cone (Sd): 324.29 cm squared
• Sound Pressure Level (spl): 100.17 db

The 12” Green Beret™ guitar speaker brings crunchy cone breakup, growling bass, great headroom, and aggressive mids together better than any other 25 watt speaker. Upgrade for Celestion™ G12M Greenback™.

Mounting Information

• Diameter: 12.2”
• Overall depth: 5.3”
• Cut-out diameter: 11.1”
• Mounting slot dimensions: 0.31”
• Number of mounting slots: 8

Thiele-Small Parameters

• Resonant Frequency (Fs): 125.30 Hz
• DC Resistance (Re): 8.05 Ohm
• Coil Inductance (Le): 0.34 mH
• Mechanical Q (Qms): 9.52
• Electromagnetic Q (Qes): 1.35
• Total Q (Qts): 1.18
• Compliance Equiv. Vol. (Vas): 10.50 cu ft
• Mech. Compliance of Susp. (Cms): 0.06 mm/N
• BL Product (BL): 11.70 T-M
• Diaphragm Mass Inc. Airload (Mms): 29.20 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.63 db

Give your listeners a tailored response of a sharp and punchy bottom-end, scooped mids, and soaring highs--keeping you in the fray at the extremes while maintaining a nice sense of sweetness in the middle of your range.

This classic 10" guitar speaker delivers a vintage sound, thanks to an alnico magnet motor that softens the tone without losing the immediacy. In addition, a vintage Kurt Müller paper cone maintains a lush profile, full-bodied sound profile that compliments your playing.

British tone guitar speaker

• 10" (250 mm) steel basket diameter
• 20 watts, 8 ohm, 96 dB SPL
• 1" copper voice coil, Kraft paper former
• 6.8 oz alnico magnet
• Kurt Müller guitar cone
• Size, Nominal (inch & mm): 10" (250 mm)
• Shape of Speaker: Round
• Speaker Type: Guitar Speaker
• Application: Musical Instruments
• Environment: Indoor
• RoHS Compliant: Yes
• Nominal Impedance (Z) (Ω): 8
• Rated Power IEC268-5 (W): 20 Watts
• Rated Impedance (Ω): 8
• Continuous Power (W): 20
• Program Power (W): 40
• Frequency Range (Hz): 65 - 6,300
• Sensitivity (dB SPL) ¹: 96
• Resonant Frequency (Fs) (Hz): 112
• DC Resistance (Re) (Ω): 6.20
• Voice Coil Inductance (Le) (mH): 0.35
• Mechanical Q Factor (Qms): 18.38
• Electrical Q Factor (Qes): 1.99
• Total Q Factor (Qts): 1.80
• Mechanical Resistance (Rms) (kg/s): 0.61
• Compliance Equivalent Volume (Vas) (L): 28.27
• Suspension Compliance (Cms) (mm/N): 0.1
• Surface Area of Diaphragm (Sd) (cm²): 397.61
• Moving Mass (Mms) (gm): 15.84
• Motor Force Factor (BL) (T•M): 5.91
• Efficiency (η₀) (%): 1.93
• Efficiency Bandwidth Product (EBP) (Fs/Qes): 56.48
• Basket Type: Cold-rolled steel
• Terminal Size (mm): 5.2 x 0.5 (Dual lug)
• Voice Coil Diameter (mm): 25.4
• Voice Coil Wire Material: Copper
• Voice Coil Former Material: Kraft paper
• Voice Coil Winding Style: Single Layer
• Magnet Material: Alnico
• Magnet Weight (g): 192.77
• Cone Body Material: Paper composite
• Cone Surround Material: Paper composite
• Dust Cap Material: Felt

The F12M-150 is a full range, LIVE response speaker, purpose designed for use with amp modellers and IRs.
Its unique design features two additional tweeter cones integrated into the main woofer cone (making it “Triple Cone”).
This enables the speaker to deliver near full-range frequency performance: from 60Hz up to 12kHz, for a rich and detailed sound, whatever your set-up.

Designed with Celestion’s Pro Audio know-how, response is flat and neutral, ensuring no unwanted colourations that could overwhelm the input signal.
But with an optimised woofer cone and lighter moving mass the F12M-150 Triple Cone is designed to closely mimic the responsiveness of a traditional guitar speaker,
delivering all the tactile feel you would expect from playing through a conventional guitar rig. It’s not just FRFR, it’s Full Range LIVE Response.

Specifications

• Nominal diameter 305mm / 12in
• Power rating 150W
• Rated impedance 8Ω
• Sensitivity 97dB
• Chassis type Pressed steel
• Magnet type Ceramic
• Magnet weight 0.9kg / 35oz
• Voice coil diameter 2in / 51mm
• Voice coil material Round copper
• Frequency range 60-12,000Hz
• Resonance frequency, Fs 70Hz
• DC resistance, Re 6.07Ω

Parameters

• D 0.26m / 10.24in
• Fs 69.4Hz
• Mms 44.772g / 1.58oz
• Qms 10.446
• Qes 0.992
• Qts 0.906
• Re 6.07
• Vas 46.89l / 1.66ft3
• BI 10.923
• Cms 0.118
• Rms 1.868
• Le (at 1kHz) 0.12

Mounting Information

• Cut-out diameter 283mm / 11.1in
• Diameter 283mm / 11.1in
• Magnet structure diameter 145mm / 5.7in
• Mounting hole dimensions 7.9mm / 0.31in Ø
• Mounting hole PCD 297mm / 11.7in
• Number of mounting holes 8
• Chassis depth (inc gasket) 94mm / 3.7in
• Magnet depth 33mm / 1.3in
• Overall depth 127mm / 5in
• Unit weight 3.6kg / 7.9lb

The 40 watt version of the Jensen Blackbird has smoother top end compared to the 100 watt version, making it suitable not only for crisp clean sounds but also good for crunchy leads.

Gene: Blues, Jazz, Rock'n Roll, Rockabilly

Technical Details:    

• Size: 12"
• Impedance: 8 Ohm
• Rated Power (RMS): 40 W
• Sensitivity @ 1 W, 1 m: 96 dB
• Resonance Frequency  fs: 93,2 Hz

Thiele/Small Parameter (8 Ohm Version)

• Re: 5.9 Ω
• Fs: 93.2 Hz
• Qms: 14.29
• Mms: 28.7 g
• Qts: 1.36
• Bxl: 8.20 Tm
• Cms: 102 µm/N
• Sd: 490.9 cm²
• Vas: 34.6 l
• Le (1kHz): 0.40 mH

The 40 watt version of the Jensen Blackbird has smoother top end compared to the 100 watt version, making it suitable not only for crisp clean sounds but also good for crunchy leads.

Gene: Blues, Jazz, Rock'n Roll, Rockabilly

Technical Details:    

• Size: 12"
• Impedance: 16 Ohm
• Rated Power (RMS): 40 W
• Sensitivity @ 1 W, 1 m: 96 dB
• Resonance Frequency  fs: 93,2 Hz

Thiele/Small Parameter (8 Ohm Version)

• Re: 5.9 Ω
• Fs: 93.2 Hz
• Qms: 14.29
• Mms: 28.7 g
• Qts: 1.36
• Bxl: 8.20 Tm
• Cms: 102 µm/N
• Sd: 490.9 cm²
• Vas: 34.6 l
• Le (1kHz): 0.40 mH

The 12” Green Beret™ guitar speaker brings crunchy cone breakup, growling bass, great headroom, and aggressive mids together better than any other 25 watt speaker. Upgrade for Celestion™ G12M Greenback™.

Unit Weight:  7.5 pounds

Mounting Information

• Diameter: 12.2”
• Overall depth: 5.3”
• Cut-out diameter: 11.1”
• Mounting slot dimensions: 0.31”
• Number of mounting slots: 8

Thiele-Small Parameters

• Resonant Frequency (Fs): 125.30 Hz
• DC Resistance (Re): 8.05 Ohm
• Coil Inductance (Le): 0.34 mH
• Mechanical Q (Qms): 9.52
• Electromagnetic Q (Qes): 1.35
• Total Q (Qts): 1.18
• Compliance Equiv. Vol. (Vas): 10.50 cu ft
• Mech. Compliance of Susp. (Cms): 0.06 mm/N
• BL Product (BL): 11.70 T-M
• Diaphragm Mass Inc. Airload (Mms): 29.20 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.63 db

Vintage American Ceramic Guitar Speaker
8″ seamed ribbed cone with small ceramic motor, replacement for Jensen C8R.

• Small Ceramic Magnet
• Power: 25 W
• Sensitivity: 94,5dB
• Weight: 1,2 kg
• VC Diameter: 1″
• 16 Ohm

Combining decades of experience with advanced measurement and analysis, the V-Type has been built using a carefully balanced 'recipe' of old and new design techniques. It produces a heady, exciting modern vintage sound that just makes you want to keep on playing: a speaker that delivers authentic Celestion tone whatever your style.The V-type is a sweet sounding speaker with a superbly balanced tonal signature that imparts a vintage musicality to your tone. Clean sounds are true across the lows, mids and highs, with just enough upper-mid chime and HF sparkle to add clarity and definition. Crank it up for a sizzling overdrive and raw rock tones, with plenty of mid-band warmth to give body and substance to lead note playing.

General Specifications

• Nominal diameter: 12", 305mm
• Power rating: 70Wrms
• Nominal impedance: Available 8Ω or 16Ω
• Sensitivity: 98dB
• Chassis type: Pressed steel
• Voice coil diameter: 1.75", 44.5mm
• Voice coil material: Round copper
• Magnet type: Ceramic
• Magnet weight: 31oz, 0.88Kg
• Frequency range: 70-5000 Hz
• Resonance frequency, Fs: 75Hz
• DC resistance, Re: Available 7.3Ω or 12.9Ω

Mounting Information

• Cut-out diameter: 11.1", 283mm
• Diameter: 12.2", 309mm
• Magnet structure diameter: 5.3”, 134mm
• Mounting slot dimensions: 0.31", 7.9mm Ø
• Mounting slot PCD: 11.7", 297mm
• Number of mounting slots: 8
• Overall depth: 4.84”, 123mm
• Unit weight: 7.2lb, 3.3kg

Tube-Town's Review

The Celestion V-Type sounds like a Vintage 30 with a touch of Greenback. Does anybody really need this? We think so, because the V-type has some clear advantages over the Vintage 30.
The biggest complaint about the Vintage 30 it the strong mid peak, which is nearly linear at 100dB between 450 - 1300 Hz. The V-Type also has a mid peak, but it starts later, around 600 Hz, and drops off sharply after 1kHz, which gives it a significantly smoother, less cluttered sound.
The V-Type also weighs quite a bit less than the Vintage 30. Your back will be grateful, and combo owners will be particularly happy.
The weight reduction follows from the use of a smaller magnet. The smaller magnet has the additional advantage that it can now be used in combos in which the magnet of a Vintage 30 would come in contact with the tubes or transformers. The V-Type also handles 10 watts more, which allows greater headroom, and is particularly useful with 50-watt amps.
Finally, the V-Type is considerably less expensive than the Vintage 30, for which your wallet will thank you.
All in all, we have to ask if the Vintage 30 is even necessary any more, as the V-Type is, to our taste, a better speaker and highly recommended as a direct replacement.
 

The brand new G8A Alnico from Warehouse Guitar Speakers. Highly recommended for the Champ, Vibro Champ, and many other 8" combos.

• Impedance: 8 Ohm
• Power: 20 Watt

One of the most versatile speakers available in the market today. With tight and focused low end, produces crystal, clear and clean tones with sweet highs and good depth and warmth, accented by shimmering but never too brittle highs and a warm harmonic tone. Articulate, when presented with overdrive distortion notes remain well defined with lots of bite. Very responsive, can be used in all types of music and at all levels of play. Excellent for 4 x 12 cabinets and combos, thanks to its limited weight. Excellent performer for both solid state and tube amplifiers, thanks to its modern power handling and tone balance.

Technical Details:    

• Size: 12"
• Impedance: 8 Ohm
• Rated Power (RMS): 100 W
• Sensitivity @ 1 W, 1 m:    97,3 dB
• Resonance Frequency  fs: 72,4 Hz

Files:

• Datasheet

Carbonfilm Resistor
Low noise, small size, high power rating
Power: 1 Watt
Voltag: 500 V working / 1000 V overload
Axial Leads
-55° C - 155° C
12 * 5 mm
RoHS