Main page » Components » Screws » Fasteners » Mounting bracket with M3 thread 10 x 11 mm

Preview: Mounting bracket with M3 thread 10 x 11 mm

Mounting bracket with M3 thread 10 x 11 mm

Mobile Preview: Mounting bracket with M3 thread 10 x 11 mm

Description

made of nickel-plated brass
with M3 thread
Hole diameter: 3.2 mm
Dimensions: 10 x 11 mm

Information about the manufacturer

Herstellerinformationen | Manufacturer Information

Tube-Town GmbH
Rumbergring 37
D-66969 Lemberg
eMail: info@tube-town.de

Customer reviews

Essential information about customer reviews We do not verify that the published reviews come from such consumers who have actually used or purchased the rated goods or services. All reviews, i.e. positive and negative, are published. No reviews that are unobjective, offensive or unrelated to the product will be published.

Unfortunately there are no review yet. Be the first who rate this product.

Customers who bought this product bought also the following products:

TT 12AX7 / ECC83 Classic V1

TT Selection: Balanced
Both systems with balanced gain

The TT12AX7 impresses with its fine and detailed reproduction of the highs, which is maintained even at high amplification levels. Due to a higher H3 part, the TT12AX7 sounds significantly cleaner than many other 12AX7/ECC83 tubes, which makes the bass range appear much tighter. We therefore especially recommend this tube for styles such as clean, crunch, and metal, where high amplification and clear transparency are required.

Electrical Characteristics

Heater voltage (Uf): 6.3V or 12.6V
Heater current (If): 300mA at 6.3V, 150mA at 12.6V
Anode voltage (Ua): Maximum 300V
Grid voltages (Ug1): -2V (typical)
Grid voltages: -50V to 0V
Anode current (Ia): 1.2mA (typical)
Anode power dissipation: Maximum 1W per triode
Anode resistance (ra): 62.5kΩ
Amplification factor (μ): 100
Transconductance (S): 1.6mA/V
Input capacitance (Cin): 1.6pF
Output capacitance (Cout): 1.6pF

Mechanical Characteristics

Socket: B9A (Noval)
Number of pins: 9

Pin Configuration

1 Anode (Triode 1)
2 Grid (Triode 1)
3 Cathode (Triode 1)
4 Heater (f)
5 Heater (f)
6 Anode (Triode 2)
7 Grid (Triode 2)
8 Cathode (Triode 2)
9 Center Heater (f)

Application Notes

Heater operation: The tube can be operated with 6.3V or 12.6V, depending on the circuit design.
Grid resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable functionality.
Coupling capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high-frequency interference.

23,95 €

Kit LNDVerb

The LNDVerb kit is based on a classic Fender reverb circuit, but uses LND 150 Mosfets instead of tubes. These can be operated at voltages as high as 500 V, to get as close as possible to the characteristics of real tubes.

The kit can be integrated into an existing amplifier or can be build as standalone unit like the Fender tube reverb.

The unit needs less than 10 mA current, so a VPump for example can be used as power supply in a standalone build. If it gets integrated into an existing amplifier the already present power supply of the amp can be used to supply the needed voltage for the unit without the need to upgrade the power transformer.

A reverb transformer of the type 125A20B or similar and a reverb tank are necessary to operate the LNDVerb. These are both not included in the kit.

The needed RCA phone sockets and potentiometers are included in the kit.

Further informations and examples of the finished unit can be found in the PDF below.

Matching parts are linked below and can be ordered with the unit if needed.

Files:

Datasheet

16,20 €