Case Handle imitation leather, black

Spezification

• Size:
  • Outside(B x H x T): 510 x 240 x 240 mm
  • Innside:(B x H x T): 474 x 204 x 240 mm
• fits Chassis: #052 (siehe list bellow)
• Hardware: none
• Weight: ca. 4 kg
• Wood:
  • Body: 18 mm Pine Plywood
  • Front/Backpanels: Body: 15 mm Pine Plywood
• Surface: untreated

Files:

• Drawing

[content:3210136]

Empty Smallhead-style amplifier housing with open back for self covering, painting or staining.
The headshell is raw and comes without any other hardware. The dimensions are the same as the normal TTC SmallHead.
Made of 15 mm FinePly plywood, corner radius 12 mm.

Specifications

• Size: 660 x 230 x 210 mm (Outside)
• Chassis-Cutout: 410 x 55 mm
• Weight: ca. 6 kg
• Wood: 15 mm Birch Plywood

[content:3210136]

• Type: Pointer Knob "Classic"
• Material: Phenolic
• Shaft Size: 6 - 6,3 mm
• Size: 27 x 15,6 mm
• Mounting: Set-Screw

Set of componentes for building the TT 5E3 / Tweed Deluxe Guitar Amp.
Please visit the >>Project page for more infos about the amp, schematics and layout.

INCLUDED:

• Transformers (Hammond 1760E und 290BEX)
• Resistors
• Capacitors
• Jacks
• Light
• Wires
• Board
• Switches
• Tubes
• Fuses & Fuesholder
• CHASSIS

NOT INCLUDED:

• Knobs
• Headshell or Combo

To build this project knowledge in electric engeneering, experience with high voltage, and the reading and understanding of schematics and dealing with measurement device is highly recommended .
There is NO step-by-step guide for beginners. The circuit and layout plan includes all relevant information. If you don't understand it then don't build it.
THIS IS NOT A BEGINNERS PROJECT !

• Type: Panel Mount Potentiometer
• Power Rating: 0,5 W
• Voltage Rating: 750 V DC
• Shaft: 6,10 mm, knurled
• Shaft length: 15 mm
• Drill Ø: 9,4 mm
• Termination: Solder lugs
• Dimension: 24 mm

• Type: Panel Mount Potentiometer
• Power Rating: 0,5 W
• Voltage Rating: 750 V DC
• Shaft: 6,10 mm, knurled
• Shaft length: 15 mm
• Drill Ø: 9,4 mm
• Termination: Solder lugs
• Dimension: 24 mm

• Type: Panel Mount Potentiometer
• Power Rating: 0,5 W
• Voltage Rating: 750 V DC
• Shaft: 6,10 mm, knurled
• Shaft length: 15 mm
• Drill Ø: 9,4 mm
• Termination: Solder lugs
• Dimension: 24 mm

• 6,3 mm jack
• mono
• Installation diameter: 10 mm

Files:

• Datasheet

4 tubes, matched as quad

JJ 6V6 Double Mica double-layered mica in the upper part of the tube. This stabilizes the tube system and significantly reduces possible vibrations that can occur due to heavy mechanical stress. This version of the JJ 6V6 was specifically designed for use in combo amplifiers.

The JJ6V6 is a beam power pentode with octal base and a maximum plate dissipation of 14W. It has fat low end and full mid tones with very good tone separation and a smooth, clean high end - in general, a very balanced tone.
Currently, the only new production 6V6 which is approved for up to 500V anode voltage in pentode operation.

Files:

• Datasheet