Main page » Components » Jacks & Plugs » Jack 6,3 mm » HICON J63MA05, Superflat Jack plug mono, angled, silver

Preview: HICON J63MA05, Superflat Jack plug mono, angled, silver

HICON J63MA05, Superflat Jack plug mono, angled, silver

Mobile Preview: HICON J63MA05, Superflat Jack plug mono, angled, silver

Description

Superflat 6.3 mm jack plug, massive pin with gold-plated tip, solder version, black metal housing, 90° angled, moisture-repellent insulation, cable Ø 4.0 - 6.4 mm, with clamping strain relief, ideal for space-saving cabling of effects pedal boards.

Manufacturer

Herstellerinformationen | Manufacturer Information
SOMMER CABLE GmbH
Humboldtstraße 32 – 36
75334 Straubenhardt
Germany
http://sommercable.com

Customer reviews (2)

Essential information about customer reviews We do not verify that the published reviews come from such consumers who have actually used or purchased the rated goods or services. All reviews, i.e. positive and negative, are published. No reviews that are unobjective, offensive or unrelated to the product will be published.

Unfortunately there are no review yet. Be the first who rate this product.

Customers who bought this product bought also the following products:

TT 12AT7 / ECC81

Warm and balanced overall sound, paired with high resolution and brilliance, which is why the TT12AT7 achieves the best results in both instrumental and audio/high-end amplifiers.

Features:

Warm and balanced sound
Excellent sound resolution and brilliance
Ideal for instrumental and audio/high-end amplifiers

Hint;
Often, 12AU7 and 12AT7 types are used instead of 12AX7 tubes in order to either reduce the overall power of the amplifier or just take back the overdrive of the preamp. Especially the 12AU7 brings a very large tonal difference compared to a 12AX7, which is usually much greater than when switching from a 12AX7 to 5751 or 12AT7.

When using a 12AU7 in a driver stage that is normally designed for 12AX7, the overall power of the power amp is usually reduced. How big this difference is depends on the amplifier or circuit. For example, a Marshall with a 12AX7 in the phase inverter stage set to volume 5 will then reach the same volume with a 12AU7 set to volume 6 (perceived volume, not measured).

Electrical Characteristics

Heater Voltage (Uf): 6.3V or 12.6V
Heater Current (If): 300mA at 6.3V, 150mA at 12.6V
Anode Voltage (Ua): Maximum 300V
Grid Voltage (Ug1): -2V (typical)
Anode Current (Ia): 10mA (typical)
Anode Power Dissipation: Maximum 2.5W per triode
Anode Resistance (ra): 11kΩ
Amplification Factor (μ): 60
Transconductance (S): 5.5mA/V
Input Capacitance (Cin): 1.6pF
Output Capacitance (Cout): 1.6pF

Mechanical Characteristics

Socket: B9A (Noval)
Number of Pins: 9

Pin Configuration

1 Anode (Triode 1)
2 Grid (Triode 1)
3 Cathode (Triode 1)
4 Heater (f)
5 Heater (f)
6 Anode (Triode 2)
7 Grid (Triode 2)
8 Cathode (Triode 2)
9 Center Heater (f)

Application Notes

Heater Operation: The tube can be operated with either 6.3V or 12.6V, depending on the circuit design.
Grid Resistors: It is recommended to use grid resistors of at least 1MΩ to ensure stable operation.
Coupling Capacitors: Capacitors with low capacitance (typically 0.1µF) are recommended to minimize high frequency disturbances.

14,20 €

Rotary Switch 1-Pol / 3-Pos - 4 A @ 250VAC - Impedance / Voltage Selector

High Power Rotary Switch - Can be used as Voltage or Impedance selector

1 pole / 3 position
Solder lugs
Shaft Diameter 6 mm, D-Shaft
Rating: 250 VAC 6(4) A
Contact Resistance: 100MOhm Max
Dielectric Intensity:
- 1500VAC / 5S for terminal and terminal
- 3000VAC / 5s for terminal and ground
Withstand Voltage: 1500VAC / min
Operating Temperature: -25~85°C
Insulation Resistance: 500 VDC, 100MOhm Min
Electrical Life: 10,000 cycles
Housing material: PA66
Ø: 22 mm
h: 17,0 mm
Ø Frontpanel drill: 10 mm

1,00 €