Potentiometer for Marshall JCM800, 1 MOhm log, Stereo

Files:

• Datasheet

If you are looking for a speaker with a classic American vibe, but need a smoother more soulful top end, look no further than the WGS G12C/S.  This is based on our popular G12C, but with a smooth cone, felt dust cap and just the right amount of edge treatment.  This speaker works great in amps where you are going for that big American clean but just need it a little softer up top.  Destined to be another WGS classic!

Thiele-Small Parameters

• Resonant Frequency (Fs): 95.68 Hz
• DC Resistance (Re): 7.47 Ohm
• Coil Inductance (Le): 0.28 mH
• Mechanical Q (Qms): 14.56
• Electromagnetic Q (Qes): 0.73
• Total Q (Qts): 0.69
• Compliance Equiv. Vol. (Vas): 19.70 cu ft
• Mech. Compliance of Susp. (Cms): 0.10 mm/N
• BL Product (BL): 12.83 T-M
• Diaphragm Mass Inc. Airload (Mms): 26.70 grams
• Surface Area of Cone (Sd): 366.10 cm squared
• Sound Pressure Level (spl): 99.54 db

• Material: Phenolic
• Shaft Size: 6 mm, knurled
• Size: 19,5 x 15,3 mm
• Mounting: Push-On, no D-Shaft

• Body: 24 mm
• Shaft: 6,35 mm, Split shaft
• PCB
• for JCM 800, 2205, 2210, etc.
• incl. one nut and one washer

• Drawing

• Body: 24 mm
• Shaft: 6,35 mm, Split shaft
• PCB
• for JCM 800, 2205, 2210, etc.
• incl. one nut and one washer

• Body: 24 mm
• Shaft: 6,35 mm, Split shaft
• PCB
• for JCM 800, 2205, 2210, etc.
• incl. one nut and one washer

• Drawing

• Power Rating: 0,25 W
• Voltage Rating: 250 V AC
• Tolerance: 20%
• Shaft: 6,35 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M8 (7,8 mm)
• Termination: Solder lugs
• Dimension: 24 mm

• Power Rating: 0,25 W
• Voltage Rating: 250 V AC
• Tolerance: 20%
• Shaft: 6,35 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M8 (7,8 mm)
• Termination: Solder lugs
• Dimension: 24 mm

• Power Rating: 0,25 W
• Voltage Rating: 250 V AC
• Tolerance: 20%
• Shaft: 6,35 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M8 (7,8 mm)
• Termination: Solder lugs
• Dimension: 24 mm

• Power Rating: 0,25 W
• Voltage Rating: 250 V AC
• Tolerance: 20%
• Shaft: 6,35 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M8 (7,8 mm)
• Termination: Solder lugs
• Dimension: 24 mm

• Power Rating: 0,25 W
• Voltage Rating: 250 V AC
• Tolerance: 20%
• Shaft: 6,35 mm, Solid Shaft
• Shaft length: 15 mm
• Drill Ø: M8 (7,8 mm)
• Termination: Solder lugs
• Dimension: 24 mm

• Body: 24 mm
• Shaft: 6,35 mm, Split shaft
• PCB
• for JCM 800, 2205, 2210, etc.
• incl. one nut and one washer

• Drawing